IOS messages

Note: Notice that certain IOS messages contain two message identifiers. The longer message number indicates the Start of change

inclusion of the subchannel set id of an alternate subchannel set to the device number. End of change

IOS000I
IOS1000I devn,chp,err,cmd,stat,[sens], [dcbblkct | op**term | trackaddress], [ser], [jobname][,sens][,text]
IOS001E
IOS1001E devn,INOPERATIVE PATH[S] xx[,chp,chp…]
IOS002A
IOS1002A devn, NO PATHS AVAILABLESTATUS FOR PATH(S) chp,chp,...
IOS003A
IOS1003A devn, INTERVENTION REQUIRED [READY THE DRIVE | RELOAD CARTRIDGE | UNLOAD CARTRIDGE.]
IOS004I
IOS RECOVERY FAILURE - DEVICES MAY BE UNAVAILABLE
IOS017I
IOS1017I ALIAS DEVICE adev IS UNBOUND
IOS019W
I/O SUBSYSTEM IS NO LONGER OPERATIONAL - SYSTEM TERMINATED
IOS050I
CHANNEL DETECTED ERROR ON dev,chp,cmd,stat [,PCHID=pppp] [,EXTSS=ss]
IOS051I
INTERFACE TIMEOUT DETECTED ONdev,chp,cmd,stat[,PCHID=pppp][,EXTSS=ss]
IOS052I
CHANNEL EVENT REPORTED FOR dev,chp,cmd,stat [,PCHID=pppp][,EXTSS=ss]
IOS053I
UTILITY SUBCHANNEL DETECTED ERROR ON Usss [EQC, CC]
IOS054I
sdddd,chp ERRORS DETECTED BY component[, component]…
IOS062E
ERROR ON CHANNEL PATHS - STOP I/O REQUESTS FROM SHARING SYSTEMS OR USE IOACTION STOP, DEV=(xxxx) TO STOP I/O TO SHARED DEVICES {—SINGLE CHANNEL PATH (chp) BEING RECOVERED| —MULTIPLE CHANNEL PATHS BEING RECOVERED }
IOS063E
ERROR ON CHANNEL PATHS - STOP I/O REQUESTS FROM SHARING SYSTEMS OR USE IOACTION STOP, DEV=(xxxx) TO STOP I/O TO SHARED DEVICES {—SINGLE CHANNEL PATH (chp) BEING RECOVERED| —MULTIPLE CHANNEL PATHS BEING RECOVERED }
IOS070E
dev, MOUNT PENDING
IOS071I
IOS1071I devn,chp,jobname,text[STATUS:statustext]
IOS072E
MIH TERMINATED, text MIH NOT RUNNING. TRY ‘SETIOS MIH,MOUNTMSG=YES | NO’
IOS073E
MIH MESSAGE PROCESSING TERMINATED
IOS074E
MIH LOGREC RECORDING PROCESSING TERMINATED
IOS075E
IOS1075E devn, RECURRING MIH CONDITION FOR THIS DEVICE
IOS076E
IOS1076E devn,chp,jobname,text,[STATUS:statustext]
IOS077E
IOS1077E devn,chp,jobname,text
IOS078I
IOS1078I devn,chpid,[jobname], I/O TIMEOUT INTERVAL HAS BEEN EXCEEDED FOR AN ACTIVE REQUEST. THE ACTIVE REQUEST HAS BEEN TERMINATED, QUEUED REQUESTS MAY HAVE ALSO BEEN TERMINATED.
IOS079I
IOS1079I devn,chpid,[jobname], I/O TIMEOUT INTERVAL HAS BEEN EXCEEDED FOR A QUEUED REQUEST. THE QUEUED REQUEST HAS BEEN TERMINATED.
IOS080I
IOS1080I devn,chpid,[jobname], I/O TIMEOUT INTERVAL HAS BEEN EXCEEDED FOR {AN ACTIVE | A QUEUED} REQUEST. [DATASET NAME=dsname]
IOS084I
IOACTION SYNTAX {ERROR | CORRECTION}: -- text
IOS085I
[source] text
IOS086I
{hh.mm.ss MIH & IOT TIMES MOUNTMSG = {YES | NO} UREC=mm:ss DASD=mm:ssHALT=mm:ss TAPE=mm:ssGRAF=mm:ss MNTS=mm:ssCTC =mm:ss COMM=mm:ssCHAR=mm:ss IOTDASD=mm:ssUSnn=mm:ssUDEV=xxx | TDEV=xxx --or-- hh.mm.ss MIH DEVICE TIMES dev=time} --or-- hh.mm.ss IOT DEVICE TIMES tdev=time} --or-- hh.mm.ss IOT HSWAP OPTIONS IO TIMING TRIGGER: text1 TERMINATE IO OPERATIONS: text2
IOS087I
{hh:mm:ss FICON DATAFICON SWITCH STATISTICS GATHERING IS text
IOS088I
hh.mm.ss CAPTURED UCB DATA CAPTURED UCB PROTECTION IS {ENABLED|DISABLED}
IOS089I
hh:mm:ss STORAGE DATAIOS BLOCKS RESIDE IN 24|31 Bit STORAGE
IOS090I
{xx,rrrr.|SETIOS.} dev IS AN INVALID DEVICE or{IECIOSxx.|SETIOS.} text UPDATE(S) COMPLETE
IOS091I
MIH. START TIMER FAILED FOR NAME name.
IOS092I
[INITIALIZATION ESTAE FAILED | INTERNAL PROCESSING ERROR] MIH NOT {RUNNING | UPDATED}
IOS093I
I/O TIMING NOT SUPPORTED FOR PAGING DEVICE dev
IOS094I
I/O TIMING IS NOT SUPPORTED FOR DEVICE dev
IOS095I
I/O TIMING IS NOT SUPPORTED FOR SWAPPABLE DEVICE dev
IOS096I
MIH INTERNAL PROCESSING ERROR
IOS097I
{hh:mm:ss} MIDAW FACILITY MIDAW FACILITY text
IOS098I
hh:mm:ss HYPERPAV DATA HYPERPAV MODE IS SET TO NO/YES/BASEONLY
IOS099I
{hh:mm:ss} EKM HOSTS PRIMARY HOSTNAME=text1 SECONDARY HOSTNAME=text2 MAX CONNECTIONS = dd1 PERMANENT CONNECTIONS = dd2[VERIFICATION WILL COMPLETE ASYNCHRONOUSLY]
IOS100I
DEVICE dev {BOXED,} [LAST PATH yy LOST,] [text]
IOS101I
DEVICE dev {FORCED OFFLINE | BOXED,} {text}
IOS102I
IOS1102I DEVICE dev {BOXED | FORCED OFFLINE}, {OPERATOR REQUEST, | PERMANENT ERROR | C.U.I.R. REQUEST} [text] or DEVICE dev BOXED, DEFERRED BOX PROCESSING COMPLETE
IOS103I
hh.mm.ss RECOVERY OPTIONS LIMITED RECOVERY TIME IS ss SECONDSLIMITED RECOVERY IS REQUESTED FOR IOTIMING DEVICESLIMITED RECOVERY IS REQUESTED FOR DASD LIMITED RECOVERY FUNCTION IS DISABLEDPATH RECOVERY SCOPE IS BY {CU | DEVICE} PATH RECOVERY INTERVAL IS interval MINUTESPATH RECOVERY THRESHOLD IS threshold ERRORSDCCF IS SET TO {MESSAGE | WAIT_STATE}
IOS104I
IOS1104I DEVICE dev {BOXED | FORCED OFFLINE}, UNCONDITIONAL RESERVE FAILED
IOS105I
IOS1105I DEVICE dev {BOXED | FORCED OFFLINE} BY UNCONDITIONAL RESERVE PROCESSING
IOS106E
VARY dev OFFLINE TO JES3
IOS107I
DEVICE dev BOX PROCESSING DEFERRED
IOS109E
IOS1109E HOT I/O RECOVERY rrrrr INITIATED FOR tttttttt DEVICE devn CHPID chp
IOS110D
IOS1110D IOS HAS DETECTED HOT I/O ON DEVICE dev THE LAST INTERRUPT FROM THIS DEVICE WAS ON CHANNEL PATH chp. THE SCD IS AT aaaaaaaa. THERE ARE nnn DEVICES WITH HOT I/O ON CHP chp. ENTER ONE OF THESE REPLIES TO TELL IOS HOW TO HANDLERECOVERY:NONE - DO NOT ATTEMPT ANY RECOVERY ACTIONDEV - LOGICALLY REMOVE THE DEVICE (BOX THE DEVICE)CU - OPERATOR HAS PHYSICALLY REMOVED THE CONTROL UNIT. THE REPLY MUST INCLUDE THE NUMBER OF EACHDEVICE ON THE CONTROL UNIT. FOR EXAMPLE, IF DEVICES250 THRU 257 and 25E ARE ON THE CONTROL UNIT, REPLYCU,250:257,25E OR CU,25E,250:257CU,K - ATTEMPT CONTROL UNIT RECOVERY. KEEP CHP ONLINEIF SUCCESSFULCHP,K - ATTEMPT CHANNEL PATH RECOVERY.KEEP CHP ONLINE IF SUCCESSFULCHP,F - FORCE THE CHANNEL PATH OFFLINE
IOS111D
IOS1111D IOS HAS DETECTED HOT I/O ON {DASD | ASSIGNABLE} DEVICE devn. THE LAST INTERRUPT FROM THIS DEVICE WAS ON CHANNEL PATH chp. THE SCD IS AT aaaaaaaa. THERE ARE nnn DEVICES WITH HOT I/O ON CHP chp. ENTER ONE OF THESE REPLIES TO TELL IOS HOW TO HANDLE RECOVERY:NONE - DO NOT ATTEMPT ANY RECOVERY ACTIONDEV - LOGICALLY REMOVE THE DEVICE (BOX THE DEVICE)CU,K - ATTEMPT CONTROL UNIT RECOVERY. KEEP CHP ONLINEIF SUCCESSFULCHP,K - ATTEMPT CHANNEL PATH RECOVERY.KEEP CHP ONLINE IF SUCCESSFULCHP,F - FORCE THE CHANNEL PATH OFFLINE
IOS112D
IOS1112D IOS HAS DETECTED HOT I/O ON {RESERVED | ASSIGNED} DEVICE devn. THE LAST INTERRUPT FROM THIS DEVICE WAS ON CHANNEL PATH chp. THE SCD IS AT aaaaaaaa. THERE ARE nnn DEVICES WITH HOT I/O ON CHP chp. ENTER ONE OF THESE REPLIES TO TELL IOS HOW TO HANDLE RECOVERY:NONE - DO NOT ATTEMPT ANY RECOVERY ACTIONDEV - LOGICALLY REMOVE THE DEVICE (BOX THE DEVICE)CU,K - ATTEMPT CONTROL UNIT RECOVERY. KEEP CHP ONLINE IFSUCCESSFULCHP,K - ATTEMPT CHANNEL PATH RECOVERY. KEEP CHP ONLINEIF SUCCESSFULCHP,F - FORCE THE CHANNEL PATH OFFLINE
IOS113W
IOS RECOVERY FAILURE - RESERVES MAY BE LOST
IOS115A
devn, PAGE DATA SET - text [REPLY U TO CONTINUE AFTER CORRECTING THE PROBLEM | RESTART THE SYSTEM TO CONTINUE AFTER CORRECTING THE PROBLEM]
IOS117A
IOS1117A IOS HAS DETECTED HOT I/O ON DEVICE devn. THE LAST INTERRUPT FROM THIS DEVICE WAS ON CHANNEL PATH chp. THE SCD IS AT aaaaaaaa. THERE ARE nnn DEVICES WITH HOT I/O ON CHP chp. ENTER ONE OF THESE REPLIES TO TELL IOS HOW TO HANDLE RECOVERY:NONE - DO NOT ATTEMPT ANY RECOVERY ACTIONDEV - LOGICALLY REMOVE THE DEVICE (BOX THE DEVICE)CU - OPERATOR HAS PHYSICALLY REMOVED THE CONTROL UNIT.THE REPLY MUST INCLUDE THE NUMBER OF EACH DEVICE OR PAV-BASE DEVICEON THE CU. FOR EXAMPLE, IF DEVICES 250–257 AND 25EARE ON THE CU, REPLY CU,250:257,25E OR CU,25E,250:257CHP,K - ATTEMPT CHP RECOVERY. KEEP CHP ONLINE IF SUCCESSFULCHP,F - FORCE THE CHANNEL PATH OFFLINE
IOS118A
IOS1118A IOS HAS DETECTED HOT I/O ON {DASD | ASSIGNABLE} DEVICE devn. THE LAST INTERRUPT FROM THIS DEVICE WAS ON CHANNEL PATH chp. THE SCD IS AT aaaaaaaa. THERE ARE nnn DEVICES WITH HOT I/O ON CHP chp. ENTER ONE OF THESE REPLIES TO TELL IOS HOW TO HANDLE RECOVERY:NONE - DO NOT ATTEMPT ANY RECOVERY ACTIONDEV - LOGICALLY REMOVE THE DEVICE (BOX THE DEVICE)CU,K - ATTEMPT CU RECOVERY. KEEP CHP ONLINE IF SUCCESSFULCHP,K - ATTEMPT CHP RECOVERY. KEEP CHP ONLINE IF SUCCESSFULCHP,F - FORCE THE CHANNEL PATH OFFLINE
IOS119A
IOS1119AIOS HAS DETECTED HOT I/O ON {RESERVED | ASSIGNED} DEVICE devn. THE LAST INTERRUPT FROM THIS DEVICE WAS ON CHANNEL PATH chp. THE SCD IS AT aaaaaaaa. THERE ARE nnn DEVICES WITH HOT I/O ON CHP chp. ENTER ONE OF THESE REPLIES TO TELL IOS HOW TO HANDLE RECOVERY:NONE - DO NOT ATTEMPT ANY RECOVERY ACTIONDEV - LOGICALLY REMOVE THE DEVICE (BOX THE DEVICE)CU,K - ATTEMPT CU RECOVERY. KEEP CHP ONLINE IF SUCCESSFULCHP,K - ATTEMPT CHP RECOVERY. KEEP CHP ONLINE IF SUCCESSFULCHP,F - FORCE THE CHANNEL PATH OFFLINE
IOS120D
IOS1120D I/O TIMED OUT FOR DEVICE devn. REPLY ‘WAIT’ FOR I/O COMPLETION OR ‘CONT’ TO CONTINUE WITH DEVICE OFFLINE
IOS121I
UNABLE TO OBTAIN CHANNEL SUBSYSTEM INFORMATION DUE TO A BUSY CONDITION. IPL CONTINUES.
IOS122I
ERROR OBTAINING CHANNEL SUBSYSTEM INFORMATION DUE TO HARDWARE FAILURE. IPL CONTINUES.
IOS123I
WAITING FOR RESPONSE(S) FROM THE FOLLOWING DEVICE(S): devn[,dev,dev,…]
IOS124A
IOS1124A STILL WAITING FOR RESPONSE FROM DEVICE dev. TOTAL WAIT TIME IS xxx SECONDS. REPLY 'CONT' OR 'WAIT'
IOS125I
IOS1125I CHPID cc IS EXPERIENCING MULTIPLE I/O TIMEOUTS CAUSING PROLONGED INITIALIZATION
IOS126I
DEVICE sdddd IS KEPT OFFLINE. text
IOS127I
THE THRESHOLD FOR THE NUMBER OF msgid MESSAGES HAS BEEN EXCEEDED. REMAINING MESSAGES ARE SUPPRESSED
IOS140W
IOS Detected Failure - System Terminated, WAIT140 RSN=rrrr rsntext
IOS150I
IOS1150I DEVICE dev NOW AVAILABLE FOR USE
IOS151I
IOS1151I DEVICE dev NOT AVAILABLE FOR USE
IOS152E
IOS1152E DEVICE dev BOXED BY SUBCHANNEL RECOVERY, DEVICE STATE UNKNOWN
IOS153E
IOS1153E DEVICE dev, BOXED STATE, NOW AVAILABLE FOR USE
IOS154I
IOS1154I DEVICE PATH (dev,chpid) NOW AVAILABLE FOR USE
IOS155I
IOS1155I DEVICE PATH(dev,chpid) NOT AVAILABLE FOR USE
IOS156I
IOS1156I THE FOLLOWING DEVICES ARE NOW AVAILABLE FOR USE: SUBCHANNEL SET: 0 xxxx,yyyy-zzzz, .... SUBCHANNEL SET: 1 xxxx,yyyy-zzzz, .... SUBCHANNEL SET: 2 xxxx,yyyy-zzzz, .... SUBCHANNEL SET: 3 xxxx,yyyy-zzzz, ....
IOS157I
IOS1157I THE FOLLOWING DEVICES ARE NOT AVAILABLE FOR USE: SUBCHANNEL SET: 0 xxxx,yyyy-zzzz, .... SUBCHANNEL SET: 1 xxxx,yyyy-zzzz, .... SUBCHANNEL SET: 2 xxxx,yyyy-zzzz, .... SUBCHANNEL SET: 3 xxxx,yyyy-zzzz, ....
IOS158I
IOS1158I PATH cc, THE FOLLOWING DEVICES ARE NOW AVAILABLE FOR USE: SUBCHANNEL SET: 0 xxxx,yyyy-zzzz, .... SUBCHANNEL SET: 1 xxxx,yyyy-zzzz, .... SUBCHANNEL SET: 2 xxxx,yyyy-zzzz, .... SUBCHANNEL SET: 3 xxxx,yyyy-zzzz, ....
IOS159I
IOS1159I PATH cc, THE FOLLOWING DEVICES ARE NOT AVAILABLE FOR USE: SUBCHANNEL SET: 0xxxx,yyyy-zzzz, .... SUBCHANNEL SET: 1xxxx,yyyy-zzzz, ....
IOS160I
CHANNEL REPORT WORDS LOST DUE TO OVERFLOW CONDITION
IOS161I
IOS1161I SUBCHANNEL ssssssss, NO MATCHING UCB FOUND
IOS162A
CHPID chp ALERT, UNSOLICITED MALFUNCTION INTERRUPT
IOS163A
CHPID chp ALERT, NO ASSOCIATED SUBCHANNEL FOR DEVICE
IOS164I
IOS1164I DEVICE devn, NO MATCHING UCB FOUND
IOS165I
IOS1165I DEVICE dev. PREFERRED PATHING {NOW | NO LONGER} IN USE
IOS166E
HYPERPAV LSS OF DEVICE dev IS NOW IN BASE ONLY MODE DUE TO ONLINE NON-FICON CHANNEL
IOS167I
DEVICE dev RESTORED BY SUBCHANNEL RECOVERY
IOS188I
CONTROL UNIT FOR DEVICE dev COULD NOT BE TRANSITIONED.IEE763I NAME= modname CODE= msg_codemsgid1 msg1[msgid2 msg2...]IEE764I END OF IOS188I RELATED MESSAGES
IOS189I
HYPERPAV MODE CHANGE INITIATED - CONTROL UNIT CONVERSION WILL COMPLETE ASYNCHRONOUSLY
IOS190I
dev, DISMOUNT VOLUME volser
IOS191I
dev, I/O ERROR READING VOLUME LABEL, cm, stat, sensbbbbbb
IOS192A
dev, MOUNT VOLUME volser OR FORCE DEVICE OFFLINE
IOS201E
START PROCESSORS STOPPED FOR MESSAGE {IOS062E | IOS063E}— RESERVES {INTACT | LOST}
IOS202E
IOS1202E CHANNEL PATH chp FORCED OFFLINE - DEVICE IS: { devn | UNKNOWN}
IOS203I
IOS1203I CHANNEL PATH chp SUCCESSFULLY RECOVERED - DEVICE IS: { devn | UNKNOWN}
IOS204E
START PROCESSORS STOPPED FOR MESSAGE {IOS062E | IOS063E}— RESERVES {INTACT | LOST}
IOS205A
ENTER REPLY
IOS206A
REPLY U TO CONTINUE PROCESSING
IOS207I
IOS1207I CONTROL UNIT FOR (devn,chp) NOT SUCCESSFULLY RECOVERED
IOS208I
IOS1208I CONTROL UNIT FOR (dev,chp) SUCCESSFULLY RECOVERED
IOS210I
PATH RECOVERY INITIATED FOR PATH chp ON CU cccc, REASON=rsntext
IOS250I
IOS1250I PATH chp BROUGHT ONLINE FOR DEVICE dev
IOS251I
IOS1251I PATH chp TAKEN OFFLINE FROM DEVICE devn
IOS275I
IOS1275I C.U.I.R. REQUEST TO QUIESCE THE FOLLOWING PATH(S): CHPID xx TO DEVICE(S) dev,dev1-dev2, … CHPID yy TO DEVICE(S) dev,dev1-dev2, …
IOS278I
IOS1278I C.U.I.R. REQUEST TO RESUME THE FOLLOWING PATH(S): CHPID xx TO DEVICE(S) dev,dev1-dev2, … CHPID yy TO DEVICE(S) dev,dev1-dev2, …
IOS281I
C.U.I.R. REQUEST SUCCESSFUL
IOS283I
IOS1283I C.U.I.R. VARY PATH(dev,xx) REJECTED, text
IOS284I
C.U.I.R. REQUEST REJECTED - VARY COMMAND PROCESSOR FAILED
IOS288A
SYSTEM-INITIATED {ONLINE |OFFLINE} RECONFIGURATION IS IN PROGRESS FOR THE FOLLOWING CHPIDS:cc,cc-cc,cc,cc-cc ... cc [WARNING: MESSAGE IS INCOMPLETE DUE TO SYSTEM ERROR.]
IOS289I
SYSTEM-INITIATED {ONLINE | OFFLINE} RECONFIGURATION HAS COMPLETED. [RECONFIGURATION WAS SUCCESSFUL FOR THE FOLLOWING CHPIDS: cc,cc-cc,cc,cc-cc ... ] [RECONFIGURATION FAILED FOR THE FOLLOWING CHPIDS: cc,cc-cc,cc,cc-cc ... ] [WARNING: MESSAGE IS INCOMPLETE DUE TO SYSTEM ERROR.]
IOS290I
C.U.I.R. REQUEST UNSUCCESSFUL
IOS291I
IOS1291I CONFIGURATION DATA COULD NOT BE READ ON PATH (devn, xx) RC=rc textline1 [textline2]
IOS292I
NUMBER OF IOS291I MESSAGES EXCEEDED NIP MAXIMUM - FURTHER IOS291I MESSAGES ARE SUPPRESSED DURING NIP
IOS300I
THE facility FACILITY IS {NOW | NO LONGER} SUPPORTED BY THE PROCESSOR
IOS301I
THE facility FACILITY IS {NOW | NO LONGER} SUPPORTED FOR CHPIDS: xx,yy-zz,…
IOS306I
dev,I/O ERROR,cmd,chp,stat,ser,text. [sssssssssssssssss…sssss]
IOS307I
TIMED OUT FOR DEVICE dddd. THE DEVICE IS OFFLINE.
IOS310A
INCORRECT REPLY
IOS320I
SWITCH PORT DECOMMISSION REQUEST FOR CHPID chp WWPN wwwwwwwwwwwwwwww
IOS321I
SWITCH PORT RECOMMISSION REQUEST FOR CHPID chp WWPN wwwwwwwwwwwwwwww
IOS322I
SWITCH PORT DECOMMISSION REQUEST FOR WWPN wwwwwwwwwwwwwwww FOR THE FOLLOWING PATHS: CHPID chp TO DEVICE(S) xxx,yyy-zzz,...,xxx,yyy-zzzCHPID chp TO DEVICE(S) xxx,yyy-zzz,...,xxx,yyy-zzz
IOS323I
SWITCH PORT RECOMMISSION REQUEST FOR WWPN wwwwwwwwwwwwwwww FOR THE FOLLOWING PATHS: CHPID chp TO DEVICE(S) xxx,yyy-zzz,...,xxx,yyy-zzzCHPID chp TO DEVICE(S) xxx,yyy-zzz,...,xxx,yyy-zzz
IOS324I
SWITCH PORT request_type REQUEST SUCCESSFUL FOR WWPN wwwwwwwwwwwwwwww
IOS325I
SWITCH PORT request_type REQUEST UNSUCCESSFUL FOR WWPN wwwwwwwwwwwwwwww
IOS326I
SWITCH PORT VARY PATH(S) REJECTED, LAST PATH TO DEVICECHPID chp TO DEVICE(S) xxx,yyy-zzz,...,xxx,yyy-zzzCHPID chp TO DEVICE(S) xxx,yyy-zzz,...,xxx,yyy-zzz
IOS327I
SWITCH PORT VARY PATH(S) REJECTED, PATH DOES NOT EXISTCHPID chp TO DEVICE(S) xxx,yyy-zzz,...,xxx,yyy-zzzCHPID chp TO DEVICE(S) xxx,yyy-zzz,...,xxx,yyy-zzz
IOS328I
SWITCH PORT VARY PATH(S) REJECTED, PATH RESERVEDCHPID chp TO DEVICE(S) xxx,yyy-zzz,...,xxx,yyy-zzzCHPID chp TO DEVICE(S) xxx,yyy-zzz,...,xxx,yyy-zzz
IOS329I
SWITCH PORT VARY PATH(S) REJECTED, DEVICE CANNOT BE ACCESSEDCHPID chp TO DEVICE(S) xxx,yyy-zzz,...,xxx,yyy-zzzCHPID chp TO DEVICE(S) xxx,yyy-zzz,...,xxx,yyy-zzz
IOS330I
SWITCH PORT VARY PATH(S) REJECTED, DEVICE UCB NOT CONNECTEDCHPID chp TO DEVICE(S) xxx,yyy-zzz,...,xxx,yyy-zzzCHPID chp TO DEVICE(S) xxx,yyy-zzz,...,xxx,yyy-zzz
IOS331I
SWITCH PORT VARY PATH(S) REJECTED, VALIDATE PATH I/O TIMED OUTCHPID chp TO DEVICE(S) xxx,yyy-zzz,...,xxx,yyy-zzzCHPID chp TO DEVICE(S) xxx,yyy-zzz,...,xxx,yyy-zzz
IOS332I
SWITCH PORT VARY PATH(S) REJECTED, VARY PROCESSOR FAILEDCHPID chp TO DEVICE(S) xxx,yyy-zzz,...,xxx,yyy-zzzCHPID chp TO DEVICE(S) xxx,yyy-zzz,...,xxx,yyy-zzz
IOS333I
SWITCH PORT VARY PATH(S) REJECTED, PATH NOT OPERATIONALCHPID chp TO DEVICE(S) xxx,yyy-zzz,...,xxx,yyy-zzzCHPID chp TO DEVICE(S) xxx,yyy-zzz,...,xxx,yyy-zzz
IOS334I
UNABLE TO CONFIGURE CHPID chp ONLINE|OFFLINE
IOS350I
DEVICE dev REQUESTED yy:yy for MIH xx:xx WILL BE USED.
IOS351I
DYNAMIC CHANNEL PATH MANAGEMENT {ACTIVE/NOT ACTIVE}
IOS352I
hh.mm.ss IOS GROUP DATAtext
IOS353I
hh.mm.ss DCM STATUStext
IOS354I
SWITCH DEVICE dddd TAKEN OFFLINE TO DCM DUE TO reason
IOS355I
PORT ADDRESS pp OF SWITCH DEVICE dddd text
IOS356I
DYNAMIC CHANNEL PATH MANAGEMENT {NOT MANAGING/MANAGING} ON SYSTEM = yyyyyyyy
IOS357I
MANUFACTURER mmm LOAD MODULE IOSTmmm NOT FOUND IN THE LNKLST
IOS358I
DYNAMIC CHANNEL PATH MANAGEMENT HAS BEEN TURNED OFF
IOS359I
SETIOS DCM COMMAND WAS NOT PROCESSED. DCM STATUS WAS NOT CHANGED.
IOS360I
SETIOS DCM COMMAND MAY HAVE NOT BEEN PROCESSED ON ALL SYSTEMS. DCM STATUS MAY NOT BE CONSISTENT ON ALL SYSTEMS.
IOS361I
CONTROL UNIT MODEL TABLE REFRESH COMPLETE
IOS363I
SWITCH DEVICE dddd NOW AVAILABLE TO DCM
IOS426I
IOS1426I devn, chp RESET ALLEGIANCE FAILURE
IOS427A
dev, chp, xxxxxx FAILURE, REPLY: WITH UR BOX OR NOOP.
IOS428I
IOS1428I dev,chp1, HAS BEEN RECOVERED THROUGH CHANNEL PATH chp2
IOS429I
IOS1429I dev,chp, COULD NOT BE RECOVERED THROUGH AN ALTERNATE CHANNEL PATH
IOS430I
dev, RESERVED TO ANOTHER SYSTEM, UNCONDITIONAL RESERVE RECOVERY NOT INVOKED.
IOS431I
DEVICE dev RESERVED TO CPU={serialmodn | UNKNOWN},LPAR ID={lparid | NONE | UNKNOWN} SYSTEM=sysname[,sysname1,sysname2, sysname3,… sysname6] | UNKNOWN
IOS443I
IOS MSI FAILED -- ESTAE RETURN CODE rc
IOS444I
IOS1444I DYNAMIC PATHING NOT {OPERATIONAL ON | REMOVED FROM} {DEVICE devn | PATH (devn,chp)}
IOS445I
PHYSICAL DEVICE IS INCONSISTENT WITH LOGICAL DEFINITION
IOS446I
I/O ERROR VALIDATING PHYSICAL DEVICE
IOS450E
IOS1450E devn, chp, text PATH TAKEN OFFLINE
IOS451I
IOS1451I dev, BOXED, text
IOS452I
IOS1452I devn chp, text
IOS500I
IOS1500I ACTIVATE RESULTS[ACTIVATE COMPLETED SUCCESSFULLY | ACTIVATE COMPLETED - WARNING MESSAGE(S) ISSUED | ACTIVATE FAILED - ERROR MESSAGE(S) ISSUED | TEST DETECTED CONDITIONS WHICH WOULD RESULT IN ACTIVATE FAILURE | TEST DETECTED NO CONDITIONS WHICH WOULD RESULT IN ACTIVATE FAILURE]rc, rsntext [COMPID = compid][MESSAGES TRUNCATED AT 20. EXCESS IN SYSLOG. TOTALMESSAGES = n.]
IOS501I
ACTIVATE CLEANUP COMPLETE
IOS502I
IOS1502I I/O CONFIGURATION CHANGED INVOKER = jobnameNEW IODF = iodfnameEDT REBUILT, NEW EDT ID = edtid[NOTE | WARN] = rc, rsntextDEVICE(S) DELETED FROM SUBCHANNEL SET 0 dev3, [dev4…].DEVICE(S) DELETED FROM SUBCHANNEL SET 1 dev3, [dev4…]. DEVICE(S) DELETED FROM SUBCHANNEL SET 2 dev3, [dev4…]. DEVICE(S) DELETED FROM SUBCHANNEL SET 3 dev3, [dev4…].DEVICE(S) ADDED FOR SUBCHANNEL SET 0 dev1, [dev2…].DEVICE(S) ADDED FOR SUBCHANNEL SET 1 dev1, [dev2…]. DEVICE(S) ADDED FOR SUBCHANNEL SET 2 dev1, [dev2…].DEVICE(S) ADDED FOR SUBCHANNEL SET 3 dev1, [dev2…].DEVICE(S) DELETED FROM SOFTWARE CONFIGURATION[FOR SUBCHANNEL SET x] dev1, [dev2...].DEVICE(S) ADDED TO SOFTWARE CONFIGURATION[FOR SUBCHANNEL SET x] dev3, [dev4...].CU(S) DELETED [FROM CSS cc] con3, [con4…].CU(S) ADDED [TO CSS cc] con1, [con2>/mv>…].CHPID(S) DELETED [FROM CSS cc] chpd3, [chpd4…].CHPID(S) ADDED [TO CSS cc] chpd1, [chpd2…].CHPID chpid DELETED FROM DEVICE(S) [IN CSS cc] dev3, [dev4…].CHPID chpid ADDED TO DEVICE(S) [IN CSS cc] dev1, [dev2…].LOGICAL PARTITIONS DELETED FROM CSS cclpname1, [lpname2…lpnamex]LOGICAL PARTITIONS ADDED TO CSS cc lpname1, [lpname2…lpnamex]PCIE FUNCTION(S) DELETED pfid1,[pfid2]PCIE FUNCTION(S) ADDED pfid1,[pfid2]
IOS503I
I/O CONFIGURATION CHANGED PARTITION partition_name DELETEDFROM CANDIDATE LIST(S) FOR DEVICE(S) [IN CSS cc] dev1, [dev2…].PARTITION partition_name ADDEDTO CANDIDATE LIST(S) FORDEVICE(S) [IN CSS cc] dev3, [dev4…].PARTITION partition_name DELETED FROM ACCESS/CANDIDATELIST(S) FOR CHPID(S)[IN CSS cc] chpd1, [chpd2…].PARTITION partition_name ADDED TO ACCESS/CANDIDATE LIST(S) FOR CHPID(S)[IN CSS cc] chpd3, [chpd4…].PARTITION partition_name DELETED FROM ACCESS/CANDIDATE LIST(S) FOR PCIE FUNCTION(S) pfid1,[pfid2]PARTITION partition_name ADDED TO ACCESS/CANDIDATE LIST(S) FOR PCIE FUNCTION(S) pfid1,[pfid2]
IOS504I
COUPLING FACILITY CONFIGURATION CHANGED {NOTE | WARN} = rc, rsntextCOUPLING FACILITY DEVICE(S) DELETED [FROM CSS cc] dev1, [dev2…].COUPLING FACILITY DEVICE(S) ADDED [TO CSS cc] dev3, [dev4…].COUPLING FACILITY CU(S) DELETED [FROM CSS cc] con1, [con2…].COUPLING FACILITY CU(S) ADDED [TO CSS cc] con3, [con4…].CF CHPID(S) DELETED [FROM CSS cc]chp1, [chp2…].CF CHPID(S) ADDED[TO CSS cc] chp3, [chp4…].
IOS505A
DYNAMIC I/O CONFIGURATION CHANGES ARE NOT ALLOWED, THE HARDWARE AND SOFTWARE CONFIGURATION DEFINITIONS DO NOT MATCH
IOS506I
hh.mm.ss I/O CONFIG DATA text
IOS507D
ACTIVATE COMMAND DID NOT COMPLETE. REPLY “WAIT” -OR- “TERM”
IOS508I
text
IOS509I
DYNAMIC I/O CONFIGURATION CHANGES ARE NOT ALLOWED, {iodfname IS NOT CATALOGED | iodfname VOLUME volume IS NOT ONLINE}
IOS510I
CONFLICTING iodfname DEVICE - dev1 USED FOR IPL, CATALOG POINTS TO dev2
IOS511A
THE PREVIOUS DYNAMIC CONFIGURATION CHANGE WAS NOT COMPLETED - ISSUE THE ACTIVATE COMMAND WITH RECOVER KEYWORD TO RECOVER
IOS512I
DYNAMIC I/O CONFIGURATION CHANGES ARE NOT ALLOWED, THE ACTIVE HARDWARE DEFINITION DOES NOT SUPPORT DYNAMIC
IOS513E
ACTIVATE STILL WAITING FOR OLD EDT TO BE DELETED - ISSUE 'D IOS,CONFIG(EDT)' TO DETERMINE OUTSTANDING BINDS
IOS515A
IOS1515A DEVICE devn DYNAMICALLY DELETED OR MODIFIED, DEDICATED ALLEGIANCE COULD NOT BE CLEARED, [PARTITION = prtition]
IOS516I
EXCESS ACTIVATE RESULTS
IOS530I
IOS530I DISCOVERY AND AUTOCONFIG[PROCESSING WAS SUCCESSFUL |PROCESSING WAS UNSUCCESSFUL]rc, rsntext [COMPID = compid]
IOS531I
IOS531I ======= ssssssss MESSAGES BEGIN =======IOS531I ======= ssssssss MESSAGES END =======
IOS532I
IOS532I diagnostic text
IOS550I
ASSIGN FAILED, DEVICE ALREADY ALLOCATED
IOS551I
NO PATHS PHYSICALLY AVAILABLE
IOS552I
PATH NOT PHYSICALLY AVAILABLE
IOS553I
I/O ERROR DURING DEVICE INITIALIZATION
IOS554I
CONFIGURATION DATA PROCESSING FAILED
IOS555I
UNABLE TO ESTABLISH DYNAMIC PATHING FOR THIS DEVICE
IOS556I
NO PATHS LOGICALLY AVAILABLE
IOS557I
SPECIFIED PATH NOT VALID
IOS558I
FUNCTION NOT PERFORMED, I/O TIMED OUT
IOS559I
FUNCTION CODE NOT SUPPORTED
IOS560I
RELEASE TEST FOR SHARED DEVICE COULD NOT BE PERFORMED
IOS561I
UNRECOVERABLE PROGRAM ERROR
IOS562I
DEVICE NOT CONNECTED
IOS563I
DEVICE IS IN BOXED STATE
IOS564I
ACTIVE TELEPROCESSING DEVICE
IOS565I
PATH OPERATIONAL BUT DEVICE COULD NOT BE ASSIGNED
IOS566I
PATH OFFLINE DUE TO CONFIG MANAGER, CANNOT BE VARIED ONLINE
IOS567I
PATH OPERATIONAL BUT DEVICE NOT BROUGHT ONLINE
IOS568I
PATH OFFLINE DUE TO C.U.I.R., CANNOT BE VARIED ONLINE
IOS569I
DEVICE IN PERMANENT ERROR STATE
IOS570I
PERMANENT ERROR WHILE ATTEMPTING TO ENABLE DEVICE
IOS571I
VOLSER FOR PATH DOES NOT MATCH VOLSER FOR DEVICE
IOS572I
I/O ERROR READING VOLUME LABEL
IOS573I
OSAD DEVICE REQUIRES A UNIT ADDRESS OF FE BUT ua FOUND
IOS574I
OSA DEVICE REQUIRES THE UNIT ADDRESS NOT BE FE
IOS575I
SENSE-ID DATA NOT VALID FOR THIS DEVICE - sense_id_data
IOS576I
OSA|IQD DEVICES REQUIRE AN OSA|IQD CHANNEL PATH BUT TYPE cc FOUND [TYPE=channel_path_type]
IOS577I
IQD INITIALIZATION FAILED, COMPLETION TABLE FULL | SET IQD PARAMETERS FAILED | FEATURE NOT INSTALLED
IOS578I
RESET OF LINK RECOVERY THRESHOLD CONDITION FAILED
IOS579E
IQD INITIALIZATION FAILED, COMPLETION TABLE FULL
IOS580E
LINK DEGRADED REPORTING CHPID=[nn | **] {INCIDENT UNIT unit-ident IC=yy INCIDENT UNIT logical interface ident| INCIDENT UNIT DATA COULD NOT BE OBTAINED} [ATTACHED UNIT unit-ident] [ATTACHED UNIT logical interface ident]
IOS581E
LINK FAILED REPORTING CHPID=[nn | **] {INCIDENT UNIT unit-ident IC=yy INCIDENT UNIT logical interface ident| INCIDENT UNIT DATA COULD NOT BE OBTAINED} [ATTACHED UNIT unit-ident] [ATTACHED UNIT logical interface ident]
IOS582I
IOS1582I PATH chp NOW OPERATIONAL AND BROUGHT ONLINE FOR DEVICE(S): dev1,dev2…
IOS583I
CAUSE OF FAILURE OF DEVICE dddd CORRECTED. REISSUE VARY COMMAND
IOS600I
IOACTION - THE FOLLOWING DEVICE(S) HAVE BEEN STOPPED: dev,dev1-dev2
IOS601I
IOACTION - DEVICES REMAIN IN THE STOPPED STATE. USE THE 'D IOS,STOP' COMMAND TO DISPLAY THE DEVICES
IOS602I
IOACTION - STOP NOT ALLOWED FOR PAGING DEVICES. THE FOLLOWING DEVICE(S) ARE IGNORED: dev dev1-dev2…
IOS603I
IOACTION - STOP NOT ALLOWED FOR SYSRES DEVICE. THE FOLLOWING DEVICE IS IGNORED: xxxx
IOS604I
IOACTION - STOP NOT ALLOWED FOR {RESERVED|ASSIGNED} OR {RESERVED|ASSIGN} PENDING DEVICES. THE FOLLOWING DEVICE(S) ARE IGNORED: dev dev1-dev2…
IOS605I
IOACTION - STOP NOT ALLOWED FOR DEVICES IN USE BY THE SYSTEM. THE FOLLOWING DEVICE(S) ARE IGNORED: dev dev1-dev2…
IOS606I
IOACTION - STOP NOT ALLOWED FOR ALL DEVICE TYPES. THE FOLLOWING DEVICE(S) ARE IGNORED: dev dev1-dev2…
IOS607I
IOACTION - THE FOLLOWING DEVICE(S) HAVE BEEN RESUMED: dev,dev1-dev2
IOS608I
IOACTION - RESUME ONLY VALID FOR DEVICES WHICH ARE STOPPED. THE FOLLOWING DEVICE(S) ARE IGNORED: dev dev1-dev2…
IOS609I
IOACTION - NO DEVICES ARE STOPPED. REQUEST IGNORED
IOS610I
IOACTION - THE FOLLOWING DEVICE(S) ARE IN THE STOPPED STATE: dev dev1-dev2…
IOS611I
IOACTION - STOP/RESUME PROCESSING FAILURE
IOS612I
IOACTION - STOP ALLOWED FOR SHARED {DASD} DEVICES ONLY. THE FOLLOWING DEVICE(S) ARE IGNORED: dev,dev1-dev2…
IOS613I
IOACTION - STOP NOT ALLOWED FOR DEVICES WITH THE FOLLOWING RESOURCE(S): XCF COUPLE DATA SET THE FOLLOWING DEVICE(S) ARE IGNORED: dev,dev1-dev2…
IOS620I
IOS COMPONENT TRACE IS UNAVAILABLE - text
IOS621I
IOS COMPONENT TRACE FAILED USING PARMLIB MEMBER membername - TRACING WILL BE INITIALIZED USING DEFAULT OPTIONS
IOS622I
IOS COMPONENT TRACE OPTION optname IS NOT VALID - text
IOS623I
IOS COMPONENT TRACE ERROR - INSUFFICIENT STORAGE FOR TRACE BUFFERS
IOS624I
IOS COMPONENT TRACE FUNCTION IS LIMITED - THE TRACE DATA SPACE COULD NOT BE CREATED
IOS625I
IOS COMPONENT TRACE OPTION optname NO LONGER SET - NOFILTER OPTION NOT SPECIFIED AND ASID/JOBNAME FILTERING NOT ACTIVE
IOS626I
IOS COMPONENT TRACE BUFFER SIZE SET TO bufsizeK
IOS627E
text1 INTERFACE WITH ENCRYPTION KEY MANAGER CANNOT BE CONNECTED DUE TO text2
IOS628E
ENCRYPTION ON DEVICE dddd HAS FAILED DUE TO text
IOS630I
hh:mm:ss ZHPF FACILITY | HIGH PERFORMANCE FICON FACILITY text
IOS631I
text ENCRYPTION KEY MANAGER WAS SUCCESSFULLY CONNECTED
IOS632I
hh.mm.ss CU GROUP DATAtextCONTROL UNITS: cuno cuno...THE GROUP IS INELIGIBLE FOR DCM FOR THE FOLLOWING REASONS:rsntext
IOS634I
IOS SYSTEM OPTIONHYPERWRITE IS status
IOS635I
STATE SAVE FOR CONTROLLER nodedesc INITIATED BY DEVICE sdddd. REQUESTOR: requestor
IOS636I
STATE SAVE FOR CONTROLLER nodedesc NOT TAKEN. Reason
IOS650I
PATH VALIDATION NOT DONE, DEVICE IN USE BY VTAM
IOS2001I
devn,INOPERATIVE PATHS chp,chp,... STATUS FOR PATH(S) chp,chp,... errortype [errormsg]
IOS2002I
devn, NO PATHS AVAILABLE chp,chp,... STATUS FOR PATH(S) chp,chp,... errortype [errormsg]
Messages with subchannel set identifiers
IEA1522I
This message indicates that there is a subchannel set identifier associated with the device number. See IEA522I for the full message explanation.
IEA1525W
This message indicates that there is a subchannel set identifier associated with the device number. See IEA525W for the full message explanation.
IEA1774I
This message indicates that there is a subchannel set identifier associated with the device number. See IEA774I for the full message explanation.
IOS1003A
This message indicates that there is a subchannel set identifier associated with the device number. See IOS003A for the full message explanation.
IOS1017I
This message indicates that there is a subchannel set identifier associated with the device number. See IOS017I for the full message explanation.
IOS1050I
This message indicates that there is a subchannel set identifier associated with the device number. See IOS050I for the full message explanation.
IOS1051E
This message indicates that there is a subchannel set identifier associated with the device number. See IOS051E for the full message explanation.
IOS1071I
This message indicates that there is a subchannel set identifier associated with the device number. See IOS071I for the full message explanation.
IOS1075E
This message indicates that there is a subchannel set identifier associated with the device number. See IOS075E for the full message explanation.
IOS1076E
This message indicates that there is a subchannel set identifier associated with the device number. See IOS076E for the full message explanation.
IOS1077E
This message indicates that there is a subchannel set identifier associated with the device number. See IOS077E for the full message explanation.
IOS1078I
This message indicates that there is a subchannel set identifier associated with the device number. See IOS078I for the full message explanation.
IOS1079I
This message indicates that there is a subchannel set identifier associated with the device number. See IOS079I for the full message explanation.
IOS1080I
This message indicates that there is a subchannel set identifier associated with the device number. See IOS080I for the full message explanation.
IOS1102I
This message indicates that there is a subchannel set identifier associated with the device number. See IOS102I for the full message explanation.
IOS1104I
This message indicates that there is a subchannel set identifier associated with the device number. See IOS104I for the full message explanation.
IOS1105I
This message indicates that there is a subchannel set identifier associated with the device number. See IOS105I for the full message explanation.
IOS1109E
This message indicates that there is a subchannel set identifier associated with the device number. See IOS109E for the full message explanation.
IOS1110D
This message indicates that there is a subchannel set identifier associated with the device number. See IOS110D for the full message explanation.
IOS1111D
This message indicates that there is a subchannel set identifier associated with the device number. See IOS111D for the full message explanation.
IOS1112D
This message indicates that there is a subchannel set identifier associated with the device number. See IOS112D for the full message explanation.
IOS1117A
This message indicates that there is a subchannel set identifier associated with the device number. See IOS117A for the full message explanation.
IOS1118A
This message indicates that there is a subchannel set identifier associated with the device number. See IOS118A for the full message explanation.
IOS1119A
This message indicates that there is a subchannel set identifier associated with the device number. See IOS119A for the full message explanation.
IOS1120D
This message indicates that there is a subchannel set identifier associated with the device number. See IOS120D for the full message explanation.
IOS1124A
This message indicates that there is a subchannel set identifier associated with the device number. See IOS124A for the full message explanation.
IOS1150I
This message indicates that there is a subchannel set identifier associated with the device number. See IOS150I for the full message explanation.
IOS1151I
This message indicates that there is a subchannel set identifier associated with the device number. See IOS151I for the full message explanation.
IOS1152E
This message indicates that there is a subchannel set identifier associated with the device number. See IOS152E for the full message explanation.
IOS1153E
This message indicates that there is a subchannel set identifier associated with the device number. See IOS153E for the full message explanation.
IOS1154I
This message indicates that there is a subchannel set identifier associated with the device number. See IOS154I for the full message explanation.
IOS1155I
This message indicates that there is a subchannel set identifier associated with the device number. See IOS155I for the full message explanation.
IOS1156I
This message indicates that there is a subchannel set identifier associated with the device number. See IOS156I for the full message explanation.
IOS1157I
This message indicates that there is a subchannel set identifier associated with the device number. See IOS157I for the full message explanation.
IOS1158I
This message indicates that there is a subchannel set identifier associated with the device number. See IOS158I for the full message explanation.
IOS1159I
This message indicates that there is a subchannel set identifier associated with the device number. See IOS159I for the full message explanation.
IOS1161I
This message indicates that there is a subchannel set identifier associated with the device number. See IOS161I for the full message explanation.
IOS1164I
This message indicates that there is a subchannel set identifier associated with the device number. See IOS164I for the full message explanation.
IOS1165I
This message indicates that there is a subchannel set identifier associated with the device number. See IOS165I for the full message explanation.
IOS1202E
This message indicates that there is a subchannel set identifier associated with the device number. See IOS202E for the full message explanation.
IOS1203I
This message indicates that there is a subchannel set identifier associated with the device number. See IOS203I for the full message explanation.
IOS1207I
This message indicates that there is a subchannel set identifier associated with the device number. See IOS207I for the full message explanation.
IOS1208I
This message indicates that there is a subchannel set identifier associated with the device number. See IOS208I for the full message explanation.
IOS1250I
This message indicates that there is a subchannel set identifier associated with the device number. See IOS250I for the full message explanation.
IOS1251I
This message indicates that there is a subchannel set identifier associated with the device number. See IOS251I for the full message explanation.
IOS1275I
This message indicates that there is a subchannel set identifier associated with the device number. See IOS275I for the full message explanation.
IOS1278I
This message indicates that there is a subchannel set identifier associated with the device number. See IOS278I for the full message explanation.
IOS1279I
This message indicates that there is a subchannel set identifier associated with the device number.
IOS1280I
This message indicates that there is a subchannel set identifier associated with the device number.
IOS1282I
This message indicates that there is a subchannel set identifier associated with the device number.
IOS1283I
This message indicates that there is a subchannel set identifier associated with the device number. See IOS283I for the full message explanation.
IOS1291I
This message indicates that there is a subchannel set identifier associated with the device number. See IOS291I for the full message explanation.
IOS1426I
This message indicates that there is a subchannel set identifier associated with the device number. See IOS426I for the full message explanation.
IOS1428I
This message indicates that there is a subchannel set identifier associated with the device number. See IOS428I for the full message explanation.
IOS1429I
This message indicates that there is a subchannel set identifier associated with the device number. See IOS429I for the full message explanation.
IOS1444I
This message indicates that there is a subchannel set identifier associated with the device number. See IOS444I for the full message explanation.
IOS1450E
This message indicates that there is a subchannel set identifier associated with the device number. See IOS450E for the full message explanation.
IOS1451I
This message indicates that there is a subchannel set identifier associated with the device number. See IOS451I for the full message explanation.
IOS1452I
This message indicates that there is a subchannel set identifier associated with the device number. See IOS452I for the full message explanation.
IOS1500I
This message indicates that there is a subchannel set identifier associated with the device number. See IOS500I for the full message explanation.
IOS1502I
This message indicates that there is a subchannel set identifier associated with the device number. See IOS502I for the full message explanation.
IOS1515A
This message indicates that there is a subchannel set identifier associated with the device number. See IOS515A for the full message explanation.
IOS1582I
This message indicates that there is a subchannel set identifier associated with the device number. See IOS582I for the full message explanation.
Basic HyperSwap Messages
IOSHS0000I
HyperSwap Services ready address
IOSHS0001I
HyperSwap Services is already active.
IOSHS0002I
Stop command received - HyperSwap Services shutting down
IOSHS0009I
reason devn
IOSHS0010I
reason devn
IOSHS0011I
MIDAW support does not match between pdevicenum and sdevicenum
IOSHS0012I
Test secondary I/O failed. Dev=sdevicenum IOSCOD=ioscode IOSTATUS=iostatus IOSSNS=iosense
IOSHS0013I
No operational paths to device pdevicenum
IOSHS0014I
Device devicenum is not in the correct state. State=devicestate Flags=deviceflags step#=stepnumber
IOSHS0015I
reason Dev=sdevicenum IOSCOD=ioscode IOSTATUS=iostatus SNS=iosense1iosense2iosense3iosense4 iosense5iosense6iosense7iosense8
IOSHS0016I
Query Unit Address Configuration I/O failed. Dev=pdevicenum IOSCOD=ioscode IOSTATUS=iostatus IOSSNS=iosense
IOSHS0018I
Initialization failed for device pdevicenum
IOSHS0019I
STATE SAVE FOR CONTROLLER nodedesc INITIATED BY DEVICE sdddd. FUNCTION: function-code
IOSHM0200I
[HyperSwap|MetroMirror] configuration actionname
IOSHM0201I
[HyperSwap|MetroMirror] configuration actionone failsReason: IOSHXSND processing failsReason: Device configuration errorReason: Swap in progressReason: Load in progressReason: Purge in progressReason: No active configurationReason: A Configuration Data existsReason: New Session not supportedReason: Unexpected result receivedReason: Configuration priority is not validReason: Prohibited by multi-target policyReason: Configuration priority conflicts with active configurationReason: Configuration replacement must be for the same typeReason: actiontwo on member memnameReason code: failrsn Devices: primdev-secdev
IOSHM0300I
HyperSwap function enabled for all PPRC pairs.
IOSHM0302I
HyperSwap reason request complete
IOSHM0303I
HyperSwap status text
IOSHM0304I
{HyperSwap|Active} configuration[s]text
IOSHM0305I
HyperSwap allowed by operator
IOSHM0306I
HyperSwap disallowed by operator
IOSHM0307I
HyperSwap disallowed: PPRC-pair suspended
IOSHM0308I
PPRC suspension eventtype for replication session sessionname eventaction eventresult. Reason reasoncode
IOSHM0309I
SETHS RESUMEIO has completed textWhere the text is: {Member: name Total devices: nnnn Devices not resumed: mmmm} {Member: name No devices processed} {Member: name Failed to process SETHS RESUMEIO}{Unable to route request to other members}
IOSHM0310I
HyperSwap unblocked by application named applname using programmatic blocking interface
IOSHM0311I
HyperSwap blocked by application named applname using programmatic blocking interface
IOSHM0313I
Basic HyperSwap system, sysname, does not support programmatic blocking.
IOSHM0314I
System, sysname, not allowed to join while Basic HyperSwap is programmatically blocked.
IOSHM0315I
HyperSwap unblocked by operator using SETHS UNBLOCK.
IOSHM0316I
SETHS UNFENCE has completed text
IOSHM0398E
SETHS command failed – sysplex routing error
IOSHM0399I
hscommand command rejected - reason
IOSHM0400I
hh:mm:ss.nn HyperSwap requested
IOSHM0401I
hh:mm:ss.nn reason HyperSwap started - trigger source Configuration: name
IOSHM0402I
hh:mm:ss.nn HyperSwap Phase – Validation of I/O connectivity starting
IOSHM0403I
hh:mm:ss.nn HyperSwap phase - Validation of I/O connectivity completed
IOSHM0404I
hh:mm:ss.nn HyperSwap Phase – Freeze and Quiesce DASD I/O starting
IOSHM0405I
hh:mm:ss.nn HyperSwap phase - Freeze and quiesce DASD I/O completed
IOSHM0406I
hh:mm:ss.nn HyperSwap phase - Failover PPRC volumes starting
IOSHM0407I
hh:mm:ss.nn HyperSwap phase - Failover PPRC volumes completed
IOSHM0408I
hh:mm:ss.nn HyperSwap phase - Swap UCBs starting
IOSHM0409I
hh:mm:ss.nn HyperSwap phase - Swap UCBs completed
IOSHM0410I
hh:mm:ss.nn HyperSwap phase - Resume DASD I/O starting
IOSHM0411I
hh:mm:ss.nn HyperSwap phase - Resume DASD I/O completed
IOSHM0412I
hh:mm:ss.nn HyperSwap phase - Cleanup starting
IOSHM0413I
hh:mm:ss.nn HyperSwap phase - Cleanup completed
IOSHM0414I
hh:mm:ss.nn reason HyperSwap Completed
IOSHM0415I
hh:mm:ss.nn reason HyperSwap Failed
IOSHM0416I
hh:mm:ss.nn reason phase skipped
IOSHM0417I
hh:mm:ss.nn HyperSwap response from sysname, API RC = return-code, Rsn = reason code
IOSHM0418I
HyperSwap Sequencing Task received unknown request
IOSHM0419I
HyperSwap Sequencing Task received request, but is not the master
IOSHM0420I
HyperSwap not done because reason
IOSHM0421I
HyperSwap ENF trigger received
IOSHM0422I
Bad return code received from IOSHXSND RC = return-code , RSN = reason-code
IOSHM0423I
hh:mm:ss.nn System sysname timed out doing HyperSwap function
IOSHM0424I
Master status = n n n
IOSHM0425I
hh:mm:ss.nn IXCMSGI error on HyperSwap function sent to system sysname
IOSHM0426I
hh:mm:ss.nn SETHS SWAP request completed
IOSHM0427I
hh:mm:ss.nn HyperSwap reason phase failed
IOSHM0428I
hh:mm:ss.nn HyperSwap failed on this processor - System Stopped
IOSHM0429I
hh:mm:ss.nn text
IOSHM0430I
hh:mm:ss.nn HyperSwap error encountered. System sysname being stopped via Policy
IOSHM0431I
hh:mm:ss.nn HyperSwap error encountered. Processing continues via policy
IOSHM0432I
hh:mm:ss.nn HyperSwap error encountered. HyperSwap sequencing is abandoned via policy
IOSHM0433I
hh:mm:ss.nn HyperSwap phase - Soft Fence starting
IOSHM0434I
hh:mm:ss.nn HyperSwap phase - Soft Fence completed
IOSHM0435I
hh:mm:ss.nn HyperSwap suspend processing for Global Mirror relationships has completed
IOSHM0436I
STATE SAVE FOR CONTROLLER nodedesc INITIATED BY DEVICE sdddd. REQUESTOR: requestor
IOSHM0500E
HyperSwap API address space not started
IOSHM0501I
Response from API for FC = function-code . RC = return-code , Rsn = reason-code
IOSHM0502I
Stop command received – adr_space_name shutting down
IOSHM0503I
adr_space_name not stopping because HyperSwap in progress
IOSHM0504I
Function code failed on device pair = pdevicenum,sdevicenum RC = return-code , Rsn = reason-code , Step# = step-num
IOSHM0600I
HyperSwap failed to create the xcf member member – RC: return-code RS: reason-code
IOSHM0601I
HyperSwap unable to obtain group information – RC: return-code RS: reason-code
IOSHM0602I
HyperSwap unable to join the group – RC: return-code RS: reason-code
IOSHM0800I
task_name task ended normally. Return code = return-code
IOSHM0801I
HyperSwap terminating due to task failure.
IOSHM0802I
HyperSwap Management Address Space already active
IOSHM0803E
HyperSwap text
IOSHM0804I
Failure in service servicename RC: return-code RSN: reason-code
IOSHM0805I
HyperSwap Enabled
IOSHM0806I
Unable to verify PPRC secondary device connectivity - configname
IOSHM0807I
HyperSwap Management Address Space ready
IOSHM0808I
HyperSwap Configuration Monitoring started, time interval = scan-int minutes
IOSHM0809I
HyperSwap Configuration Monitoring stopped
IOSHM0810I
HyperSwap disallowed: Monitor detected condition
IOSHM0811I
task_name ended abnormally. System code = completion-code -reason-code
IOSHM0812I
task_name ended abnormally. User code = completion-code -reason-code
IOSHM0813I
HyperSwap CTRACE definition failed using CTIBHI00. RC=, rcRSN=rsn
IOSHM0814I
Failure in service servicename RetValue: return-value RC: return-code RSN: reason-code
IOSHM0815I
Socket connection rejected. Maximum number of connections ( numconn) reached.
IOSHM0817A
Basic HyperSwap is waiting for {OMVS|TCP/IP} to become available.
IOSHM0818I
Configuration configname will now be used for HyperSwap
IOSHM0819I
Configuration configname is not preferred for HyperSwap - reason
IOSHM0900I
HyperSwap request not accepted – RC:return-code RS:reason-code
IOSPF Messages
IOSPF100I
Device sdddd could not be found.
IOSPF101I
Device sdddd is not online.
IOSPF102I
Device sdddd has no operational paths.
IOSPF103I
Device sdddd has only one online path.
IOSPF104I
Device sdddd has all online paths go through one switch.
IOSPF105I
Device sdddd has only non-preferred paths online.
IOSPF106I
Device sdddd has only preferred paths online.
IOSPF107I
Device sdddd has only one preferred path online.
IOSPF108I
Device sdddd has all CHPIDs share a single point of failure, component indicators = xxxxxxxxxxxxxxxxxxxxxxxx (model dependent).
IOSPF109I
Device sdddd has all control unit interfaces share d1 of d2 common components.
IOSPF150I
Devices sddd1 and sddd2 are the same device.
IOSPF151I
Devices sddd1 and sddd2 share a logical subsystem.
IOSPF152I
Devices sddd1 and sddd2 share the same physical control unit
IOSPF153I
Devices sddd1 and sddd2 have all paths share the same switch.
IOSPF154I
Devices sddd1 and sddd2 have all CHPIDs share a single point of failure, component indicators = xxxxxxxxxxxxxxxxxxxxxxxx (model dependent).
IOSPF155I
Devices sddd1 and sddd2 have all control unit interfaces share d1 of d2 common components.
IOSPF200I
Volume vvvvvv could not be found.
IOSPF201I
Volume vvvvvv is not valid.
IOSPF202I
Volume vvvvvv (sdddd) has no operational paths.
IOSPF203I
Volume vvvvvv (sdddd) has only one online path.
IOSPF204I
Volume vvvvvv (sdddd) has all online paths go through the same switch.
IOSPF205I
Volume vvvvvv has only non-preferred paths online.
IOSPF206I
Volume vvvvvv (sdddd) has only preferred paths online.
IOSPF207I
Volume vvvvvv (sdddd) has only one preferred path online.
IOSPF208I
Volume vvvvvv (sdddd) has all CHPIDs share a single point of failure, component indicators = xxxxxxxxxxxxxxxxxxxxxxxx (model dependent).
IOSPF209I
Volume vvvvvv (sdddd) has all control unit interfaces share d1 of d2 common components.
IOSPF250I
Volumes vvvvv1 (sddd1) and vvvvv2 (sddd2) are the same volume.
IOSPF251I
Volumes vvvvv1 (sddd1) and vvvvv2 (sddd2) share a logical subsystem.
IOSPF252I
Volumes vvvvv1 (sddd1) and vvvvv2 (sddd2) share the same physical control unit
IOSPF253I
Volumes vvvvv1 (sddd1) and vvvvv2 (sddd2) have all paths share the same switch.
IOSPF254I
Volumes vvvvv1 (sddd1) and vvvvv2 (sddd2) have all CHPIDs share a single point of failure, component indicators = xxxxxxxxxxxxxxxxxxxxxxxx (model dependent).
IOSPF255I
Volumes vvvvv1 ( sddd1) and vvvvv2 ( sddd2) have all control unit interfaces share d1 of d2 common components.
IOSPF300I
Volume vvvvvv (sdddd) with dsn could not be found.
IOSPF301I
Volume vvvvvv (sdddd) with dsn is not online.
IOSPF302I
Volume vvvvvv (sdddd) with dsn has no operational paths.
IOSPF303I
Volume vvvvvv (sdddd) with dsn has only one online path.
IOSPF304I
Volumevvvvvv (sdddd) with dsn has all online paths go through one switch.
IOSPF305I
Volume vvvvvv (sdddd) with dsm has only non-preferred paths online.
IOSPF306I
Volume vvvvvv (sdddd) with dsn has only preferred paths online.
IOSPF307I
Volume vvvvvv (sdddd) with dsn has only one preferred path online.
IOSPF308I
Volume vvvvvv (sdddd) with dsn has all CHPIDs share a single point of failure, component indicators = xxxxxxxxxxxxxxxxxxxxxxxx (model dependent).
IOSPF309I
Volume vvvvvv (sdddd) with dsn has all control unit interfaces share d1 of d2 common components.
IOSPF350I
Volumes vvvvv1 (sddd1) with dsn1 and vvvvv2 (sddd2) with dsn2 are on the same volume.
IOSPF351I
Volumes vvvvv1 (sddd1) with dsn1 and vvvvv2 (sddd2) with dsn2 share a logical subsystem (LSS).
IOSPF352I
Volumes vvvvv1 (sddd1) with dsn1 and vvvvv2 (sddd2) with dsn2 share the same physical control unit
IOSPF353I
Volumes vvvvv1 (sddd1) with dsn1 and vvvvv2 (sddd2) with dsn2 have all paths share the same switch.
IOSPF354I
Volumes with vvvvv1 (sddd1) with dsn1 and vvvvv2 (sddd2) with dsn2 have all CHPIDs share a single point of failure, component indicators = xxxxxxxxxxxxxxxxxxxxxxxx (model dependent).
IOSPF355I
Volumes vvvvv1 (vvvvv1) with dsn1 and vvvvv2 (sddd2) with dsn2 have all control unit interfaces share d1 of d2 common components.
IOSPF500I
All online paths on device sdddd share common hardware components on snd: hardware component 0, hardware component 1, hardware component 2, hardware component 3, hardware component 4, hardware component 5, hardware component 6, hardware component 7
IOSPF501I
All online paths on devices sddd1 and sddd2 share common hardware components on snd: hardware component 0, hardware component 1, hardware component 2, hardware component 3, hardware component 4, hardware component 5, hardware component 6, hardware component 7
IOSPF502I
All online paths on volume vvvvv (sdddd) share common hardware components on snd: hardware component 0, hardware component 1, hardware component 2, hardware component 3, hardware component 4, hardware component 5, hardware component 6, hardware component 7
IOSPF503I
All online paths on volumes vvvvv1 (sddd1) and vvvvv2 (sddd2) share common hardware components on snd: hardware component 0, hardware component 1, hardware component 2, hardware component 3, hardware component 4, hardware component 5, hardware component 6, hardware component 7
IOSPF504I
All online paths on volume vvvvv (sdddd) with dsn share common hardware components on snd: hardware component 0, hardware component 1, hardware component 2, hardware component 3, hardware component 4, hardware component 5, hardware component 6, hardware component 7
IOSPF505I
All online paths on volumes vvvvv1 (sddd1) with dsn1 and vvvvv2 (sddd2) with dsn2 share common hardware components on snd: hardware component 0, hardware component 1, hardware component 2, hardware component 3, hardware component 4, hardware component 5, hardware component 6, hardware component 7