IOS502I

Explanation
The system sends this message to the hard-copy
log when the system completes processing of an ACTIVATE request initiated
via an ACTIVATE request or an HCD ACTIVATE panel. An installation
can use this message to do the following: Audit configuration changes
Allow message-based automation programs to make the added input/output
(I/O) components available for use

In the message text: INVOKER=jobname
The name of the program that issued the ACTIVATE request. If the
ACTIVATE request was issued through the hardware configuration definition
(HCD) application programmer interface (API), this field contains
the name of the program that invoked the API. If the ACTIVATE request
was issued through the HCD panels, this field contains the userid
on which HCD is running. If the operator entered the ACTIVATE request,
this field contains OPERATOR.
NEW IODF = iodfname
The name of the IODF that contains the I/O configuration definition
that was activated.
EDT REBUILT, NEW EDT ID = edtid
Two-character identifier for the new EDT that was built.
[NOTE | WARN] = rc, rsntext
A four-digit hexadecimal reason code and an associated informational
or attention message.  See the explanation of message IOS500I for
descriptions of these messages.
DEVICE(S) ADDED TO SOFTWARE CONFIGURATION dev1, [dev2...]
A list of devices that were added to the software configuration
by the activate request.
DEVICE(S) DELETED FROM SOFTWARE CONFIGURATION dev3, [dev4...]
A list of devices that were deleted from the software configuration
by the activate request.
DEVICE(S) ADDED dev1, [dev2…]
A list of devices that were added to the hardware configuration
by the activate request.
DEVICE(S) DELETED dev3, [dev4…]
A list of devices that were deleted from the hardware configuration
by the activate request. If FOR SUBCHANNEL SET x is
displayed, shows the subchannel set for the devices.

CU(S) ADDED con1,[con2…]
A list of control units that were added by the activate request.
CU(S) DELETED con3, [con4…]
A list of control units that were deleted by the activate request.
If you have not explicitly deleted the devices which are attached
to the deleted control unit, subsequent display of the UCBs for these
devices will show them as offline.
CHPID(S) ADDED chpd1, [chpd2…]
A list of channel path identifiers that were added by the activate
request.
CHPID(S) DELETED chpd3, [chpd4…]
A list of channel path identifiers that were deleted by the activate
request.
FROM CSS cc
Indicates the logical channel subsystem for the deleted devices.
TO CSS cc
Indicates the logical channel subsystem for the devices being
added.
CHPID chpid ADDED TO DEVICE(S) [IN CSS cc]dev1,[dev2…]
The activate request added the specified channel path to the specified
list of devices. If IN CSS cc is
displayed, shows the logical channel subsystem for the devices.
CHPID chpid DELETED FROM DEVICE(S) [TO
CSS cc]dev3, [dev4…]
The activate request deleted the specified channel path from the
specified list of devices.If IN CSS cc is
displayed, shows the logical channel subsystem for the devices.

LOGICAL PARTITIONS DELETED FROM CSS cc lpname1,
[lpname2…lpnamex]
The activate request deleted the logical partition from the I/O
configuration.
LOGICAL PARTITIONS ADDED TO FROM CSS cc lpname1,
[lpname2…lpnamex]
The activate request added the logical partition to the I/O configuration.
PCIE FUNCTION(S) DELETED pfid1,[pfid2]
A list of PCIe functions deleted from the I/O configuration by
the activate request.
PCIE FUNCTION(S) ADDED pfid1,[pfid2]
A list of PCIe functions added to the I/O configuration by the
activate request.

System action
The system sends this message to the hardcopy
log when processing of the ACTIVATE request completes. The system
continues processing with the new I/O configuration definition.  

Source
Input/output supervisor (IOS)

Routing code
Note 13

Descriptor code
-