PM90159: ABEND0C9 OCCURRED AT DIVIDE INSTRUCTION OF EKYZM10X +838.

Obtain the fix for this APAR.

APAR status

• Closed as program error.

Error description

• ABEND0C9 occurred at DIVIDE instruction of EKYZM10X +838 in
  EKYZ130X. The date of the input record may be 2012/04/12, and
  this DPROP execution date is 2013/03/26. The GAP is very large
  between the running date of the Apply BMP and the date of a
  DPROP MQ message being processed. A divide instruction results
  an overflow condition and ABEND0C9 occurred.
  

Local fix

Problem summary

• ****************************************************************
  * USERS AFFECTED: Users of the IMS DataPropagator Version 3    *
  *                 Release 1 MQSeries based Asynchronous        *
  *                 Propagation Apply program.                   *
  ****************************************************************
  * PROBLEM DESCRIPTION: The Apply program may terminate after   *
  *                      an ABENDS0C9.                           *
  ****************************************************************
  * RECOMMENDATION: INSTALL CORRECTIVE SERVICE FOR APAR/PTF      *
  ****************************************************************
  The IMS DataPropagator MQ asynchronous Apply program may
  fail following an S0C9 ABEND.  This problem may be encountered
  when processing an MQSeries message that was created by the
  Capture program from more than 248 days prior to running the
  Apply program.  This problem is thus not expected to occur
  during normal processing situations where near real-time
  propagation and message latency is more typical.
  

Problem conclusion

• The reported problem occurred as a result of an overflow
  condition which may arise when an incoming Capture message to
  the Apply program is approximately 248 days or older.
     Modules have been changed to trap and avoid this potential
  overflow condition for the type of extremely old message
  described previously.
     The number of seconds reported in the "DELAY" section of the
  Apply statistics has been increased to seven digits from the
  original five digits.  This expansion allows reporting up to
  a maximum "delay" of over 115 days.
     If a delay of more than 9999999.99 seconds is encountered a
  new message will be issued as follows:
  EKYI422W UPDATE DELAY COMPUTATION RESULTS IN EXTREMELY LARGE
           VALUE WITH NUMERICAL OVERFLOW WHICH CANNOT BE REPORTED.
     Note that delay statistics reported that are within the
  overflow state will be displayed as follows:
     ------------ DELAY -------------
            AVG        MIN        MAX
     9999999.99 9999999.99 9999999.99
     When delay statistics fall below the overflow threshold
  during the Apply that encountered an overflow, normal reporting
  will resume, for example:
     ------------ DELAY -------------
            AVG        MIN        MAX
           1.01       1.01       1.01
     ------------ DELAY -------------
            AVG        MIN        MAX
           0.25       0.25       0.25
  Final summary statistics will not (can not) contain reliable
  values for the entire queue processing once an overflow has
  occurred.  Thus any reported summary delay will ignore overflow
  and only consider otherwise valid delay times.  For example
  using the above example:
     ------------ DELAY -------------
            AVG        MIN        MAX
           0.63       0.25       1.01
  

Temporary fix

Comments

APAR Information

• APAR is sysrouted FROM one or more of the following:

• APAR is sysrouted TO one or more of the following:

  UK97476

Modules/Macros

• EKYI420X EKYI430X EKYZI25E EKYZM10X
  

Fix information

• Fixed component name

  IMS DATA PROPAG

• Fixed component ID

  5655E5200

Applicable component levels

• R310 PSY UK97476

     UP13/09/17 P F309

Fix is available

• Select the PTF appropriate for your component level. You will be required to sign in. Distribution on physical media is not available in all countries.