HD48283: GSD / SHAPE FILLET FAILS WITH INTERNAL ERROR, BUT IT CAN B BE CR EATED BY CLEARING SOME SELECTIONS

APAR status

• Closed as program error.

Error description

• GSD / SHAPE FILLET FAILS WITH INTERNAL
  ERROR, BUT IT CAN B BE CREATED BY CLEARING
  SOME SELECTIONS
  .
  1. File -> Open the attached CATPart
  2. Click Shape Fillet icon and select as follow:
  Fillet Type: BiTangent Fillet
  Support 1 : Extrude.1
  Support 2 : Extrude.2
  Law Relimiter 2: Point.2
  ---> Both OK and Preview buttons become active.
  and click OK button
  ===> Then Update Error can be detected with
  message:
  Fillet.1: No entry found for error id 0x00000064.
  3. Click OK on the Update Error panel
  4. Click MB3 on Law Relimiter 1 -> Clear Selection
  5. Click MB3 on Law Relimiter 2 -> Clear Selection
  6. Click OK button
  ---> Then the shape fillet can be created.
  Remark:
  Same behavior can be detected at the modification
  of the Radius
  of the shape fillet as follow:
  1) Double click Fillet.1
  2) Change the Radius value from 10mm to 15mm
  ---> At this time, both OK and Preview buttons are
  inactive.
  3) Select as follow:
  Law Relimiter 2: Point.2
  ---> Both OK and Preview buttons become active.
  4) Click OK button
  ===> Then Update Error can be detected with
  message:
  Fillet.1: No entry found for error id 0x00000064.
  5) Click OK on the Update Error panel
  6) Click MB3 on Law Relimiter 1 -> Clear Selection
  7) Click MB3 on Law Relimiter 2 -> Clear Selection
  8) Click OK button
  ---> Then the shape fillet can be modified.
  EXPECTED RESULT:
  The shape fillet should be created without detecting
  the Update Error.
  

Local fix

Problem summary

• GSD / SHAPE FILLET FAILS WITH INTERNAL
  ERROR, BUT IT CAN B BE CREATED BY CLEARING
  SOME SELECTIONS
  .
  1. File -> Open the attached CATPart
  2. Click Shape Fillet icon and select as follow:
  Fillet Type: BiTangent Fillet
  Support 1 : Extrude.1
  Support 2 : Extrude.2
  Law Relimiter 2: Point.2
  ---> Both OK and Preview buttons become active.
  and click OK button
  ===> Then Update Error can be detected with
  message:
  Fillet.1: No entry found for error id 0x00000064.
  3. Click OK on the Update Error panel
  4. Click MB3 on Law Relimiter 1 -> Clear Selection
  5. Click MB3 on Law Relimiter 2 -> Clear Selection
  6. Click OK button
  ---> Then the shape fillet can be created.
  Remark:
  Same behavior can be detected at the modification
  of the Radius
  of the shape fillet as follow:
  1) Double click Fillet.1
  2) Change the Radius value from 10mm to 15mm
  ---> At this time, both OK and Preview buttons are
  inactive.
  3) Select as follow:
  Law Relimiter 2: Point.2
  ---> Both OK and Preview buttons become active.
  4) Click OK button
  ===> Then Update Error can be detected with
  message:
  Fillet.1: No entry found for error id 0x00000064.
  5) Click OK on the Update Error panel
  6) Click MB3 on Law Relimiter 1 -> Clear Selection
  7) Click MB3 on Law Relimiter 2 -> Clear Selection
  8) Click OK button
  ---> Then the shape fillet can be modified.
  EXPECTED RESULT:
  The shape fillet should be created without detecting
  the Update Error.
  

Problem conclusion

• THIS PROBLEM WILL BE FIXED ON Virtual Design  VERSION V5R17
  GA level.
  Additional Closure Information:
  THIS PROBLEM WILL BE FIXED ON CATIA VERSION
  5 RELEASE 17 GA level.
  .
  Incident Diagnosis
  GSD / SHAPE FILLET FAILS WITH INTERNAL
  ERROR, BUT IT CAN B BE CREATED BY CLEARING
  SOME SELECTIONS
  .
  Correction Explanation
  Variable shape fillet with infinite spine were not
  correctly managed.
  .
  Answer and By-Pass
  It is now possible to create fillet with infinite spine
  with constant radius law without specifing relimiters.
  Some additional test (versionned) has also been
  added:
  - if law is constant -> relimiters are not mandatory
  - if law is not constant -> relimiters are mandatory
  - if spine is infinite, we cannot define variable
  radius law.
  

Temporary fix

Comments

APAR Information

• APAR is sysrouted FROM one or more of the following:

• APAR is sysrouted TO one or more of the following:

Fix information

• Fixed component name

  CATIA V5 NT>XP

• Fixed component ID

  569151000

Applicable component levels

• R519 PSN

     UP