Download
Version
59C0
Release Date
2 June 2009
Downloadable File
File link | File size | File description |
---|---|---|
4,296 | CHANGE HISTORY for IBM LTO1 Tape Drive Firmware Update | |
7,573 | README for IBM LTO1 Tape Drive Firmware Update | |
992,831 | IBM LTO1 59C0 linux firmware update (.sh) for IBM xSeries |
Abstract
IBM LTO1 Tape Drive Firmware Update
Download Description
Note: You now have two ways of downloading files with the *.sh extension. You can use either the IBM Download Director, or the HTTP protocol to download these files. Do NOT use FTP as this will only cause the file to open your browser.
Change history
Severity: Suggested
This release note summarizes the firmware changes made to the IBM LTO1 tape drive firmware from version 36UC to version 59C0.
Number Description
- A new function is added allowing customer to enable a periodic clean cycle of
every 40 full file passes. - A particular write command sequence can cause write error due to a flag being reset unexpectedly.
- On a cartridge with invalid End of Data, less than 4 datasets recorded, SILI bit
on in variable length mode and an over length condition, the first attempt to
read will result in a permanent error. - Perform alternate gain adjustments and retry to CM read when initial read fails.
- The write errors corrected counter is incorrectly decremented when a write
permanent error occurs. - When write command completes with an error, the flag indicating data to be
flushed from buffer is cleared and incorrect good status returned. - The firmware incorrectly translates status from a write permanent error which
may result in a stuck cartridge. - The Read Position command will intermittently report incorrect values after a
buffer flush. - When in Early Warning area and an error is encountered and recovered, a Write FileMark of zero will return an error.
- If an internal abort is issued in a READ operation while Error Recovery is in
progress, a hang will result. - Add flag to indicate that Hardware error has been reported during Diagnostics.
- Misreporting Locate Failure with error code 4 instead of 6.
- A check condition will incorrectly be reported if a Report Density
command is issued with media field set to 1 and a corrupted cartridge is loaded. - Certain servo errors can cause the drive to randomly skip sections of tape
during writing. If there were numerous old datasets in this area during a read
operation, the drive could not find the next Valid dataset. A permanent read
error would occur, even though the next valid dataset was written correctly. - Unexpectedly large lateral movement of tape during drive start/stop motion
would cause the drive to be unable to find servo signals. This would cause
various write errors, including permanent write errors. - Drive diagnostic F was changed help diagnose drive issues which affect
cartridge capacity. - A cartridge with a corrupt Cartridge Memory would cause the drive to hang and
FSC 2025, 2076, 2095 might be reported by the drive. - TapeAlert flag 22 is not cleared when Cleaner Cartridge is removed.
Off
Document Location
Worldwide
[{"Type":"HW","Business Unit":{"code":"BU016","label":"Multiple Vendor Support"},"Product":{"code":"HW189","label":"Older System x->xSeries 360"},"Platform":[{"code":"PF042","label":"Caldera"},{"code":"PF047","label":"SurePOS"}],"Line of Business":{"code":"","label":""}},{"Type":"HW","Business Unit":{"code":"BU016","label":"Multiple Vendor Support"},"Product":{"code":"HW18L","label":"Older System x->xSeries 330"},"Platform":[{"code":"PF042","label":"Caldera"},{"code":"PF047","label":"SurePOS"}],"Line of Business":{"code":"","label":""}},{"Type":"HW","Business Unit":{"code":"BU016","label":"Multiple Vendor Support"},"Product":{"code":"HW18R","label":"Older System x->xSeries 250"},"Platform":[{"code":"PF042","label":"Caldera"},{"code":"PF047","label":"SurePOS"}],"Line of Business":{"code":"","label":""}},{"Type":"HW","Business Unit":{"code":"BU016","label":"Multiple Vendor Support"},"Product":{"code":"HW191","label":"Older System x->xSeries 440"},"Platform":[{"code":"PF042","label":"Caldera"},{"code":"PF047","label":"SurePOS"}],"Line of Business":{"code":"","label":""}},{"Type":"HW","Business Unit":{"code":"BU016","label":"Multiple Vendor Support"},"Product":{"code":"HW19K","label":"Older System x->xSeries 255"},"Platform":[{"code":"PF042","label":"Caldera"},{"code":"PF047","label":"SurePOS"}],"Line of Business":{"code":"","label":""}},{"Type":"HW","Business Unit":{"code":"BU016","label":"Multiple Vendor Support"},"Product":{"code":"HW19S","label":"Older System x->xSeries 345"},"Platform":[{"code":"PF042","label":"Caldera"},{"code":"PF047","label":"SurePOS"}],"Line of Business":{"code":"","label":""}},{"Type":"HW","Business Unit":{"code":"BU016","label":"Multiple Vendor Support"},"Product":{"code":"HW19T","label":"Older System x->xSeries 225"},"Platform":[{"code":"PF042","label":"Caldera"},{"code":"PF047","label":"SurePOS"}],"Line of Business":{"code":"","label":""}},{"Type":"HW","Business Unit":{"code":"BU016","label":"Multiple Vendor Support"},"Product":{"code":"HW19W","label":"Older System x->xSeries 450"},"Platform":[{"code":"PF042","label":"Caldera"},{"code":"PF047","label":"SurePOS"}],"Line of Business":{"code":"","label":""}},{"Type":"HW","Business Unit":{"code":"BU016","label":"Multiple Vendor Support"},"Product":{"code":"HW20N","label":"xSeries 226"},"Platform":[{"code":"PF042","label":"Caldera"},{"code":"PF047","label":"SurePOS"}],"Line of Business":{"code":"","label":""}}]
Was this topic helpful?
Document Information
Modified date:
02 August 2013
UID
ibm1MIGR-5080904