IGW540I

all

Explanation
This message is generated when the D SMS,SMSVSAM,QUIESCE
operator command is entered. This command will display the status
of all VSAM spheres that are opened for VSAM/RLS processing
and are being QUIESCED.
This command reports information only on
the command where the command is being entered.
If the SMSVSAM
server address space is not active, message IGW451I is returned.
This
message has 5 variations.
Variation 1 is displayed when the
SMSVSAM address space has partially completed initialization, but
the code to handle QUIESCE has not been completely initialized: IGW540I hh.mm.ss DISPLAY SMS,SMSVSAM,QUIESCE
DISPLAY SMSVSAM QUIESCE SPHERE IS REJECTED.
QUIESCE INITIALIZATION HAS NOT COMPLETED.

Variation
2 is displayed when there is not quiesce activity currently active
on the system where the quiesce command was entered: IGW540I hh.mm.ss DISPLAY SMS,SMSVSAM,QUIESCE
DISPLAY SMSVSAM QUIESCE SPHERE IS REJECTED.
NO QUIESCE EVENTS ARE ACTIVE ON THIS SYSTEM.

Variation
3 is displayed when the command is not able to get the correct quiesce
serialization: IGW540I hh.mm.ss DISPLAY SMS,SMSVSAM,QUIESCE
DISPLAY SMSVSAM QUIESCE SPHERE IS REJECTED.
UNABLE TO OBTAIN REQUIRED QUIESCE SERIALIZATION.

Variation
4 is displayed when there are quiesce events active: IGW540I hh.mm.ss DISPLAY SMS,SMSVSAM,QUIESCE
SPHERE NAME: yyyyyyyy.yyyyyyyy.yyyyyyyy
SYSTEM NAME: ssssssss  START TIME: hh.mm.ss TOTAL ELAPSE TIME: hh.mm.ss

PARTICIPATING SUB-SYSTEM STATUS: SCHEDULED: COMPLETED: ELAPSE:
 SUB-SYSTEM NAME: aaaaaaaa       hh.ss.mm   hh.ss.mm   hh.ss.mm
 SUB-SYSTEM NAME: aaaaaaaa       hh.ss.mm   hh.ss.mm   hh.ss.mm

SPHERE NAME: yyyyyyyy.yyyyyyyy.yyyyyyyy
SYSTEM NAME: SYSTEM1 START TIME: hh.mm.ss TOTAL ELAPSE TIME: hh.mm.ss

PARTICIPATING SUB-SYSTEM STATUS: SCHEDULED: COMPLETED: ELAPSE:
 SUB-SYSTEM NAME: aaaaaaaa       hh.ss.mm   hh.ss.mm   hh.ss.mm
 SUB-SYSTEM NAME: aaaaaaaa       hh.ss.mm   hh.ss.mm   hh.ss.mm

In
the message text: hh.mm.ss
The time in hours (00-23), in minutes (00-59), and seconds (00-59).
ssssssss
The MVS™ system name.
yyyyyyyy
The sphere name.
aaaaaaaa
The sub-system name that is processing the quiesce request.

START TIME is the time that system ssssssss
started processing the quiesce sphere event for sphere  yyyyyyyy.yyyyyyyy.yyyyyyyy.yyyyyyyy.
TOTAL
ELAPSE TIME is the total time that has elapsed since system ssssssss
started processing the quiesce sphere event for sphere  yyyyyyyy.yyyyyyyy.yyyyyyyy.yyyyyyyy.
SCHEDULED 
is the time that the quiesce  event was started on this system for
sub-system aaaaaaaa.
COMPLETED is
the time that sub-system  aaaaaaaa completed the quiesce event.
If the sub-system has not completed the quiesce event, the COMPLETED
field will show --.--.--.).
ELAPSE is the time interval
that sub-system aaaaaaaa required to complete the quiesce request.
If
more than 200 lines of display information is generated from the command,
then the following two lines will be placed at the bottom of the display
to indicate that more information is available for display: *********** MORE QUIESCE SPHERE DATA ***********
********** RESPOND TO IGW540A MESSAGE ***********

Variation
5 is the action message that is presented when there is still more
data available to the display; this is a WTOR: *67 IGW540A SMSVSAM DISPLAY QUIESCE HAS REACHED WTOR MAXIMUM.
REPLY 'CONTINUE' TO PROCEED, OR 'END' TO STOP DISPLAY.

If
the operator responds 'CONTINUE',  then 200 more lines of the display
will be presented. If the operator responds 'END', then the command
will be completed and no more action is required.
The IGW540A
message is only presented when the bottom of the display
contains the MORE QUIESCE SPHERE DATA lines.

System action
Processing continues.

Operator response
Present the output to the system programmer
to determine if an excessive amount of time has elapsed since the
quiesce sphere event has started.

System programmer response
Reply 'CONTINUE' to allow the display
command to present the next 200 lines of output, or 'END' to have
the display command to end.

Source
IGWSTMSG