Explanation
This message provides the report details for the
output of the XQUERY command for a storage control report. It is associated
with header messages ANTQ8241I and ANTQ8242I. The report shows the
status of the storage control sessions within an XRC session.
- ssid –
- Identifies the storage subsystem ID associated with the specified
storage control session.
- scsn –
- Identifies the storage control session name assigned by the user.
- scid –
- Identifies the session ID assigned by the storage control to the
storage control session. If it cannot be determined it is reported
as "**".
- status –
- Provides the status of the storage control session when the command
was issued. Optimal performance is indicated when the field is blank
(session is active). The status can be one of the following:
- (blank) – Active
- B – One or more devices on this primary storage control
has exceeded the maximum number of record sets that are allowed for
a storage control session.
- D – One or more devices on this primary storage control
is being blocked.
- E – I/O error obtaining status from the storage control
- L – Long busy condition
- N – Storage control session is not found
- Q – Quiesced
- R – Utility device is reserved by this system
- S – Suspended session
- T – Storage control session has timed out
- U – Unable to determine utility volume for the storage
control
- & – Utility device is reserved by another system
- 1 – Record update I/O has 1 storage control path
blocked
- 2 – Record update I/O has 2 storage control paths
blocked
- 3 – Record update I/O has 3 storage control paths
blocked
- 4 – Record update I/O has 4 storage control paths
blocked
- residual_count –
- Specifies the number of pending record updates in the storage
control at the time the command was issued. It indicates how many
records exist in the storage control buffers for the XRC session.
- utility_volume –
- Identifies the volume serial number of the volume
being used by the data mover as a utility device path for the storage
control identified by the storage subsystem ID. This field can be "******" if
the utility volume is either offline or cannot be determined. If this
is a temporary condition (caused by a concurrent XDELPAIR or XSUSPEND
command), reissue the command to report a new utility volume, if one
exists. For a session using Enhanced Multi-Reader,
multiple instances of ANTQ8243I can appear in the STORAGECONTROL DETAIL
report for the same SSID and SC SN values, one for each storage control
session in the enhanced multi-reader group. In that report, an indicator
of the multi-reader state will appear between the RES CNT and UTIL
VOL columns. In the STORAGECONTROL (without DETAIL) report, a single
ANTQ8243I appears for the primary session of the enhanced multi-reader
group, without the additional indicator column.
The volume
serial number can have one of the following characters in front of
the serial number:
- An asterisk (*) indicates that the storage control session scsn for
the storage subsystem ssid has the fixed utility
device of utility_volume.
- An 's' indicates that XRC has detected that the utility_volume was
previously a fixed utility device but the current storage control
status indicates that the device is now a floating utility device.
- An 'h' indicates that XRC has detected that the utility_volume was
previously a floating utility device but the current storage control
status indicates that the device is now a fixed utility device.
- A 'p' indicates that this line in the XQUERY
output describes the primary storage control session ID of the enhanced
multi-reader session group. The significance of a primary storage
control session is that it might not be deleted from the XRC session
until all associated auxiliary storage control session IDs have been
deleted.
- An 'a' indicates that this line in the XQUERY
output describes an auxiliary storage control session ID of an enhanced
multi-reader session group. Auxiliary session IDs might be added and
deleted as needed, although volumes in the enhanced multi-reader group
are suspended.
- A blank indicates that both the software and the storage control
have the same floating utility volume setting.
- timeout –
- Specifies the current timeout interval for the storage control.
For a quiesced storage control, it is the time remaining before the
storage control ends the active session.
- storage_control_time –
- Specifies the timestamp of the current record being processed
by the storage control.
System action
XRC functions are active.
System programmer response
If the command has been accepted and
this message has not been displayed at either the system console log
or at the user ID specified by the MSGROUTEID parameter, see message
ANTT0099I.
Source
Extended remote copy (XRC).