(BF67) Linux reference codes

The Linux® operating system detected a failure in the emulex driver.

The first five characters (BFxxx) of these SRCs indicate the driver or subsystem responsible for the error, and the last three characters specifies the error condition. The last three characters of the SRCs are arranged such that 1xx is lowest severity and Fxx is highest severity. For example:

Use the following table to locate the last four characters of the (BF67) Linux SRC that you want to find, then perform the suggested actions.

Note:
If the suggested action in the Description/Action column does not work (or if that column does not contain a suggested action), use the action specified in the Failing Item column.

Table 1. (BF67) Linux reference codes

Reference Code Description/Action Perform all actions before exchanging Failing Items Failing Item
7800 An ELS IOCB command was posted to a ring and did not complete within ULP timeout seconds.

If no ELS command is going through the adapter, reboot the system.

 NEXTLVL
7801 The driver attempted to issue READ_SPARAM mailbox command to the HBA but there were no buffer available. This message indicates one of the following conditions:
  • A possible lack of memory resources. Try increasing the lpfc num_bufs configuration parameter to allocate more buffers
  • A possible driver buffer management problem
 NEXTLVL
7802 The driver attempted to issue REG_LOGIN mailbox command to the HBA but there were no buffer available. This message indicates one of the following conditions:
  • A possible lack of memory resources. Try increasing the lpfc num_bufs configuration parameter to allocate more buffers
  • A possible driver buffer management problem
 NEXTLVL
7803 This message indicates one of the following conditions:
  • Port rsp ring put index is greater than the size of rsp ring
  • Port cmd ring get index is greater than the size of cmd ring
  • Port cmd ring get index is greater than the size of cmd ring
  • The assigned I/O iotag is greater than the max allowed
  • The assigned I/O iotag is greater than the max allowed

This error might indicate a software driver, firmware or hardware problem.

 NEXTLVL
7804 The Rctl/Type of a received frame did not match any for the configured masks for the specified ring.

This error might indicate a software driver or firmware problem.

 NEXTLVL
7805 Received an unknown IOCB command completion.

This error might indicate a software driver or firmware problem.

 NEXTLVL
7806 The driver wan unable to find a matching command for the completion received on the specified ring.

This error might indicate a software driver or firmware problem.

 NEXTLVL
7807 A unknown mailbox command completed.

This error might indicate a software driver, firmware or hardware problem.

 NEXTLVL
7808 The configuration parameter for scan-down is out of range.

Software driver error.

 NEXTLVL
7809 The driver attempted to register the HBA interrupt service routine with the host operating system but failed.

This error might indicate a hardware or driver problem.

 NEXTLVL
780A The driver manages its own memory for internal usage. This error indicates a problem occurred in the driver memory management routines. This error might also indicate the host system in low on memory resources.

This error might indicate a driver or host operating system problem.

 NEXTLVL
780B This message indicates one of the following conditions:
  • ASCII string to hex conversion failed. Input byte count less than 1
  • ASCII string to hex conversion failed. Input byte count greater than the max <num>
  • ASCII string to hex conversion failed. The output buffer byte size is less than one-half of the input byte count. Every two input chars (bytes) require one output byte

This error might indicate a software driver problem.

 NEXTLVL
7A00 The driver decided to drop an ELS Response ring entry.

This error might indicate a software driver or firmware problem.

 NEXTLVL
7A01 Received a mailbox completion interrupt and there are no outstanding mailbox commands.

This error might indicate a hardware or firmware problem. Update firmware.

 NEXTLVL
7A02 The driver issued a CONFIG_LINK mbox command to the HBA that failed.

This error might indicate a firmware or hardware problem.

Update firmware or replace adapter.

 NEXTLVL
7A03 The driver issued a READ_SPARAM mbox command to the HBA that failed.

This error might indicate a firmware or hardware problem.

 NEXTLVL
7A04 The driver issued a CLEAR_LA mbox command to the HBA that failed.

This error might indicate a firmware or hardware problem.

 NEXTLVL
7A05 A read nvparams mailbox command failed during config port.

This error might indicate a hardware or firmware problem.

 NEXTLVL
7A06 The driver cannot find the specified buffer in its mapping table.

This error might indicate a software driver or firmware problem.

 NEXTLVL
7A07 The adapter failed during power-up diagnostics after it was reset.

This error might indicate a hardware or firmware problem.

 NEXTLVL
7A08 The adapter failed during power-up diagnostics after it was reset.

This error might indicate a hardware or firmware problem.

 NEXTLVL
7A09 Adapter initialization failed when issuing READ_REV mailbox command.

This error might indicate a hardware or firmware problem.

 NEXTLVL
7A0A Outdated firmware was detected during initialization.

This error might indicate a hardware or firmware problem.

Update firmware.

 NEXTLVL
7A0B Adapter initialization failed when issuing DUMP_VPD mailbox command.

This error might indicate a hardware or firmware problem.

 NEXTLVL
7A0C Adapter initialization failed when issuing CONFIG_PORT mailbox command.

This error might indicate a hardware or firmware problem.

 NEXTLVL
7A0D Adapter initialization failed when issuing CFG_RING mailbox command.

This error might indicate a hardware or firmware problem.

 NEXTLVL
7A0E Adapter initialization failed when issuing CONFIG_LINK mailbox command.

This error might indicate a hardware or firmware problem.

 NEXTLVL
7A0F Adapter initialization failed when issuing READ_SPARM mailbox command.

This error might indicate a hardware or firmware problem.

 NEXTLVL
7A10 Adapter initialization failed when issuing READ_CONFIG mailbox command.

This error might indicate a hardware or firmware problem.

 NEXTLVL
7A11 Adapter initialization failed when issuing INIT_LINK mailbox command.

This error might indicate a hardware or firmware problem.

 NEXTLVL
7A12 The driver received an interrupt indicting a possible hardware problem.

This error might indicate a hardware or firmware problem.

 NEXTLVL
Send feedback |  Rate this page