Statements and parameters for DEVSUPxx
- ALVERSION=
- Specifies whether AL tapes are created using Version 3 or Version 4 standards. In all cases, the
Volume Mount (VOLMT) exit can override the version that is specified by ALVERSION. See z/OS DFSMS Installation Exits for more information about VOLMT. Restriction: ALVERSION is valid only if the AL tape data set is being opened for output processing to the first file of the first or only volume of the data set.
- 3
- Specifies that new AL labels are written as ISO/ANSI/FIPS Version 3. The Version 3 and 4 labels that are current are preserved.
- 4
- Specifies that new AL labels are written as ISO/ANSI Version 4. The Version 3 and 4 labels that are current are preserved.
- FORCE3
- Specifies that all AL labels are forced as ISO/ANSI/FIPS Version 3, including any current version 3 and 4 labels.
- FORCE4
- Specifies that all AL labels are forced as ISO/ANSI Version 4, including any current version 3 and 4 labels.
- COMPACT=
- NO
- Specifies that data is not to be stored in a compacted format on each 3480, 3490 or 359x tape subsystem, unless overridden by the user. If no installation default is provided through the DEVSUPxx member, and storing data in a compacted format is not explicitly requested on a DD statement, dynamic allocation request, the MOD=parameter on the JES3 *CALL, DJ command, or DCB macro, then the system uses the compaction default for the device. For example, the compaction default for a 3480 is NOCOMP. To determine the compaction default for a particular device, see the planning or migration documentation that accompanies the device.
- YES
- Specifies that data is to be stored in a compacted format on each 3480, 3490, or 359x tape subsystem, unless overridden by the user.
- COPYSDB=
- Supplies the system-level default for the SDB keyword for IEBGENER. The system uses this value
to set a code in the DFA that any application program can use. See z/OS DFSMSdfp Advanced Services. The keyword is designed for
use by assembler language programs that copy data sets.
The meanings for the keyword values are described in z/OS DFSMSdfp Utilities. The default is no code in the DFA, which means that IEBGENER assumes SDB=INPUT.
Note: DFSORT's ICEGENER uses the DFSORT SDB installation value as its default. The IBM®-supplied default is SDB=INPUT. See z/OS DFSORT Installation and Customization for details. - DDRSIZELIM=
- Specifies the limit on storage usage for Tape DDR swap. The value xxxx is a number from 1 to 1000 and specifies the number of megabytes of main storage that is allowed to be used in a Tape DDR swap. The system stores this value in the data facilities area (DFA), for use by the system and by application programs. Tape DDR swap checks this value to make sure that the total amount of storage that is required in swap processing does not exceed the specified limit. If it does, DDR terminates the swap and prints an error message. The default value for this parameter is 1000 megabytes.
- {ENABLE | DISABLE}(feature)
- Enables or disables a particular feature, where feature can be any one of the
following choices:
- AOM496I
- Enables or disables the issuing of the AOM496I status message on the console for transparent
cloud tiering operations.
- ENABLE(AOM496I)
- Enables the issuing of the AOM496I status message on the console for transparent cloud tiering
operations. The following message is issued when ENABLE(AOM496I) is present in a DEVSUPxx
member:
'IEA253I DEVSUP AOM496I IS ENABLED'
- DISABLE(AOM496I)
- Disables the issuing of the AOM496I status message on the console for transparent cloud tiering
operations. This is the default. The following message is issued when DISABLE(AOM496I) is present in
a DEVSUPxx member:
'IEA253I DEVSUP AOM496I IS DISABLED'
Default: DISABLE(AOM496I) - LRECCW_PER_EOSCP=xNN
-
- xNN
- A two-digit hexadecimal number from x01 - x030 equivalent to decimal 1 - 48 to indicate how many
LRE CCWs can be chained per channel program for Erase-On-Scratch function. Note that each LRE CCW
can erase up to 255 tracks. Note: For release z/OS R21, this new function does not have any effect to change the number of Erase commands. Only the new keyword is supported for z/OS R21 toleration
Default: LRECCW_PER_EOSCP=x30 or 48 Note if XRC is active on the device, the number of LRE CCWs per EOS channel program is fixed at 5 and cannot be changed.If a valid hexadecimal number is specified, this message will be displayed on the console. IEA253I DEVSUP NUMBER OF LRE CCWS PER EOS CHANNEL PROGRAM = xNN
If the keyword is not specified, there will be no message. - MULTINCRFLC(NO|YES)
-
- NO
- Disables the Multiple Incremental FlashCopy or the Change Recording Version 2 function.
- YES
- Enables the Multiple Incremental FlashCopy or the Change Recording Version 2 function.
Default: YES.If Multiple Incremental FlashCopy is enabled by default or by setting MULTINCRFLC=YES in the DEVSUPxx parmlib member, an IEA253I message is logged.IEA253I DEVSUP MULTIPLE INCREMENTAL FLASHCOPY: CHANGE RECORDING V2
If MULTINCRFLC=NO is specified followed by using the SET DEVSUP command to refresh the DEVSUPxx parmlib member, the IEA253I message is not logged.
If Multiple Incremental FlashCopy is enabled by installing the enablement OA45412 PTF followed by an IPL of the system, the MULTIPLE INCREMENTAL FLASHCOPY: CHANGE RECORDING V2 status will be seen in the output of the F DEVMAN,REPORT console command. Refer to z/OS MVS System Commands for information about the F DEVMAN,REPORT console command.
If Multiple Incremental FlashCopy is disabled by issuing SET DEVSUP=XX with MULTINCRFLC=NO in the DEVSUPxx parmlib member, the MULTIPLE INCREMENTAL FLASHCOPY: CHANGE RECORDING V2 status is not in the output of the F DEVMAN,REPORT command.
- PPRCMT
- Enables or disables the Multi-Target PPRC support.
- DISABLE(PPRCMT)
- When the PPRCMT feature is disabled, functionality will be in single target mode.
- ENABLE(PPRCMT)
- When the PPRCMT feature is enabled, support is available to allow a device to be the primary of more than one PPRC pair.
Default: DISABLE(PPRCMT) - PPRCSUM
- Enables or disables the PPRCSUM feature of the Device Manager.
- If the PPRCSUM feature is enabled or disabled after IPL, one device in every control unit must be varied online to activate the feature.
- Because the PPRCSUM feature gets disabled after an HCD dynamic activation, one device in every control unit must be varied online to activate the feature after an ACTIVATE IODF.
- DISABLE(PPRCSUM)
- When the PPRCSUM feature is disabled, PPRC suspend notification for individual devices is displayed in message IEA494I.
- ENABLE(PPRCSUM)
- Enables the PPRCSUM feature of the Device Manager, which means using message IEA075I instead of
IEA494I to report devices that transition to PPRC suspended state. The PPRCSUM feature significantly
reduces the volume of messages that are written to the console when devices in a PPRC relationship
are suspended. If you enable PPRCSUM, the system will issue an IEA075I message every 5 seconds or
when the last device in the control unit has suspended to summarize the PPRC state for all devices
in the control unit. This continues until all PPRC state transitions have completed. Note: If GDPS® or other PPRC monitoring software is active, make sure that the appropriate version of this software is installed before enabling PPRCSUM.
Default: DISABLE(PPRCSUM) - REFUCB
- Enables or disables the automatic REFUCB function of the Device Manager:
- DISABLE(REFUCB)
- When the REFUCB feature is disabled, the system does not refresh the UCB when a DSS COPY, RESTORE, or ICKDSF FLASHCPY, INIT or REFORMAT operation has changed either the volser or the VTOC location.
- ENABLE(REFUCB)
- When the REFUCB feature is enabled, the system automatically updates the UCB when device support
software detects that a DSS COPY, RESTORE, or ICKDSF FLASHCPY, INIT or
REFORMAT operation has changed either the volser or the VTOC location, the DEVMAN REFUCB service is
invoked on each system in the sysplex that has REFUCB enabled.
- If the device is ONLINE, REFUCB issues a VARY ONLINE, UNCONDITIONAL command, which updates both the volser and VTOC location in the UCB.
- If the device is OFFLINE, no action is taken.
Default: ENABLE(REFUCB) - REFVTOC
- Enables or disables the automatic REFVTOC function of the Device Manager:
- DISABLE(REFVTOC)
- When the REFVTOC feature is disabled and the system detects a volume expansion, the system issues message IEA019I, but the VTOC is not rebuilt. An ICKDSF Batch job must be submitted to rebuild the VTOC before the newly added space on the volume can be used.
- ENABLE(REFVTOC)
- When the REFVTOC feature is enabled and the system detects a volume expansion, the system issues message IEA019I. If the volume is online, the Device Manager causes the volume VTOC to be rebuilt. This allows the newly added space on the volume to be used by the system.
Default: ENABLE(REFVTOC) - SSR
- Enables or disables the secondary space reduction support of the Device Manager.
- DISABLE(SSR)
- Disables the secondary space reduction support.
- ENABLE(SSR)
- Enables the secondary space reduction support.
Default: ENABLE(SSR) - ZERO_DIR_PDS
- Enables or fails the allocation of a PDS with zero directory block defined in the JCL. If the
ZERO_DIR_PDS keyword is not specified, no message is logged during IPL.
- ENABLE(ZERO_DIR_PDS)
- Allow the allocation of PDS with zero directory block specified in the JCL explicitly or
implicitly. When ENABLE(ZERO_DIR_PDS) is specified, message IEA253I is logged during IPL time or when the SET DEVSUP=xx command is entered.
IEA253I DEVSUP ALLOW ALLOCATION OF ZERO DIRECTORY PDS
- DISABLE(ZERO_DIR_PDS)
- Fail the allocation of PDS with zero directory block specified in the JCL explicitly or
implicitly.When DISABLE(ZERO_DIR_PDS) is specified, message IEA253I is logged during IPL or when the SET DEVSUP=xx command is entered.
IEA253I DEVSUP FAIL ALLOCATION OF ZERO DIRECTORY PDS
Default: ENABLE(ZERO_DIR_PDS) - ENFORCE_DC_MEDIA
- Specifies whether dataclass media policies are enforced for stand-alone,
non-specific mounts.
- ALLMEDIATY
- Specifies that dataclass media policies are enforced for all stand-alone, non-specific mounts.
- MEDIA5PLUS
- Specifies that dataclass media policies are enforced for all stand-alone, non-specific mounts for any of the 3592 tape cartridge media types.
- EOSV2=
- NO
- For a device in PPRC relationship, Erase-On-Scratch issued a one-channel program to erase one track at a time until all tracks are erased.
- YES
- Erase-On-Scratch can erase up to 255 tracks in a single channel
program, if the PPRC primary and secondary devices are maintained
on the same level of microcode fix as shown in the
following table.
Machine type Microcode level DS8100/DS8300 64.36.89.0 DS8700 76.31.70.0 DS8800 86.31.86.0
Default: NONote: There is no IEA253I message logged for this option.- EASYTIERHINTS=
- NO
- Disables the Easy-Tier Copy Temperature function for software-defined storage. This disables Query/Set Temperature functions that is used to direct data placement in the Disk Controller. NO is the default.
- YES
- Enables the Easy-Tier Copy Temperature function for software-defined storage. This enables Query/Set Temperature functions that is used to direct data placement in the Disk Controller.
If the Easy-Tier Copy Temperature function for software-defined storage is enabled by setting EASYTIERHINTS=YES in the DEVSUPxx member of SYS1.PARMLIB, an IEA253I message is logged.IEA253I DEVSUP EASY-TIER FOR SOFTWARE DEFINED STORAGE
If EASYTIERHINTS=NO is specified followed by issuing the SET DEVSUP=xx command to refresh the PARMLIB member, the IEA253I message is not logged.
If the Easy-Tier Copy Temperature function for software-defined storage is enabled by setting EASYTIERHINTS=YES in the DEVSUPxx member of the PARMLIB followed by an IPL of the system, the EASY-TIER FOR SOFTWARE DEFINED STORAGE status will be seen in the output of the F DEVMAN,REPORT console command. Refer to z/OS MVS System Commands for usage of the F DEVMAN,REPORT console command.
If the Easy-Tier Copy Temperature function for software-defined storage is disabled by issuing SET DEVSUP=XX with EASYTIERHINTS=NO in the PARMLIB member, the EASY-TIER FOR SOFTWARE DEFINED STORAGE status will not be seen in the output of the F DEVMAN,REPORT command.
- EXPIRATION_MESSAGE=
-
- ALWAYS
- Normal expiration date processing occurs when opening a non-VSAM
data set on DASD. Set the parameter to ALWAYS to allow OPEN to process
expiration date processing as it normally does, that is, by issuing
message IEC507D and the optional associated TSO/E message IEC108I
when any attempt is made to open for output a data set on DASD for
which the expiration date has not yet occurred.Note: This keyword has no affect for data sets on magnetic tape even if you specify NEVER.
- NEVER
- Disables expiration date processing when opening a non-VSAM data set on DASD. Set the parameter to NEVER if you want OPEN to disable expiration date processing when opening all non-VSAM data sets on DASD for output processing. Specifying NEVER eliminates the message IEC507D and the optional associated message IEC108I for all non-VSAM data sets on DASD. Therefore, any authorized user can open an expiration date protected non-VSAM DASD data set for output without requiring the operator to allow access.
Default: ALWAYS - FLASHCOPYTOXRC
-
- NO
- Disable support for Remote Pair FlashCopy for XRC environments.At IPL, or when the SET DEVSUP=xx command is issued with FLASHCOPYTOXRC=NO in DEVSUPxx, this message is displayed:
IEA253I DEVSUP DISALLOW REMOTE PAIR FLASHCOPY TO XRC
- YES
- Enable support for Remote Pair FlashCopy for XRC environments.At IPL, or when the SET DEVSUP=xx command is issued with FLASHCOPYTOXRC=YES in DEVSUPxx, this message is displayed:
IEA253I DEVSUP ALLOW REMOTE PAIR FLASHCOPY TO XRC
If FLASHCOPYTOXRC is not specified at all in DEVSUPxx, no messages are issued.
- GREATER_253=
-
- NO
- Specifies that in a system managed tape environment, SMS on a scratch allocation request will retain its current tape subsystem (device pool) limit of 253. Also refer to the “Tape subsystem (device pool) limitation” section in z/OS DFSMS OAM Planning, Installation, and Storage Administration Guide for Tape Libraries for additional information.
- YES
- Specifies that in a system managed tape environment, SMS on a scratch allocation request can return more than 253 tape subsystems (device pools) to MVS™ Allocation. Before enabling this support, ensure that all systems in the sysplex can support the increased limit (z/OS® V2R2 or later or z/OS V1R13 and V2R1 with SMS APAR OA44354), otherwise jobs could incur abends. Also refer to the “Tape subsystem (device pool) limitation” section in z/OS DFSMS OAM Planning, Installation, and Storage Administration Guide for Tape Libraries.
Default: NO - ICKDSF_NODSEXIST=
-
- NO
- Disables the ICKDSF NODSEXIST parameter as the default for the ICKDSF INIT command. If the
NODSEXIST parameter is disabled and the device contains data sets, the ICKDSF INIT command is not
terminated because data sets exist.
If ICKDSF NODSEXIST=NO is specified, an IEA253I message is logged at IPL or after a 'SET DEVSUP=xx' command is issued.
- YES
- Enables the ICKDSF NODSEXIST parameter to be the default for the ICKDSF INIT command. If the
NODSEXIST parameter is the default and the device contains data sets other than the VTOC index data
set or VVDS, the command terminates and message ICK32179I is in the job output. See Device Support Facilities (ICKDSF) User's Guide and Reference for more
details.
If ICKDSF_NODSEXIST=YES is specified, an IEA253I message is logged at IPL or after a 'SET DEVSUP=xx' command is issued.
Default: NONote: If an online INIT is attempted on a volume that has been initialized as a Data Facility Storage Management Subsystem (DFSMS) managed volume and data sets other than the VTOC index data set or VVDS exist, the command terminates and message ICK32177I is in the job output. See Device Support Facilities (ICKDSF) User's Guide and Reference for more details. - ICKDSF_VERIFYOFFLINE=
-
- NO
- Disable the ICKDSF VERIFYOFFLINE parameter as default. If you want to make sure that the device
is offline to all host systems, you must specify the VERIFYOFFLINE parameter.
If ICKDSF_VERIFYOFFLINE=NO is specified, an IEA253I message is logged at IPL or after a 'SET DEVSUP=xx' command is issued.
- YES
- Enable the ICKDSF VERIFYOFFLINE parameter to be defaulted if all the following are true:
- UNIT parameter is specified
- Storage control microcode support exists
- z/OS software support exists
- Device is not a minidisk
If ICKDSF_VERIFYOFFLINE=YES is specified, an IEAV253I DEVSUP ENABLED ICKDSF VERIFYOFFLINE PARAMETER DEFAULT message is also logged. If the keyword is not specified, no message is logged.
Default: YES - JES3_ALLOC_ASSIST=
-
- NO
- Specifies that the allocation assistance support (available with the TS7700 Virtualization Engine) is not to be used by JES3. JES3 scratch and specific allocation requests will continue to be directed to the single library image referred to as the composite library with no knowledge of the underlying clusters (distributed libraries).
- YES
- Specifies that the allocation assist support (available with the TS7700 Virtualization Engine)
is being enabled for usage with JES3. With this support enabled, scratch allocations can be directed
(through TS7700's management class policies) to specific clusters (distributed libraries) and
specific allocations are directed to a preferred list of clusters (distributed libraries) returned
by the library.
Before enabling this support refer to the setup steps in the “JES3 Considerations” section in z/OS DFSMS OAM Planning, Installation, and Storage Administration Guide for Tape Libraries. If you do not perform the setup before enabling this support, jobs might incur abends.
Default: NO - MTL_NO_DC_WORM_OK
- Specifies that you can use WORM tape in an MTL environment without a Dataclass specification for WORM.
- NON_VSAM_XTIOT=
-
- NO
- Disables support for XTIOT, uncaptured UCB, and DSAB control blocks that reside above the 16-megabyte line for data sets that use BSAM, QSAM, or BPAM. The default value for NON_VSAM_XTIOT is NO.
- YES
- Enables support for XTIOT, uncaptured UCB, and DSAB control blocks that reside above the 16-megabyte line for data sets that use BSAM, QSAM, or BPAM.
- OCE_ABEND_DESCRIP=
-
Note: As of z/OS V1R13 with the installation of APAR OA37957, the enablement of this function is now provided through the MPFLSTxx parmlib member. For details, refer to Controlling verbose message production.
- NO
- Specifies that OPEN, EOV, and CLOSE abend messages will not include a descriptive text for the associated numeric abend and numeric return code. To diagnose and respond to the messages, you might have to look up the codes.
- YES
- Specifies that abend messages for selected OPEN, EOV, and CLOSE determinant errors include descriptive text for the associated numeric abend code and numeric return code. This option can eliminate the need to look up the meanings of the abend and reason codes that are returned in the messages.
Default: NO - PPRCSYMCONFG=
-
- NO
- Specifies that the PPRC/Metro Mirror HyperSwap configuration is not symmetrical. This indicates the same volume address is not used to identify primary and secondary volumes in a pair relationship.
- YES
- Specifies that the PPRC/Metro Mirror HyperSwap configuration is symmetrical. This indicates the same volume address is used to identify both primary and secondary volumes in a pair relationship.
Default: NOA symmetrical logical configuration is a duplicate configurations where the Metro Mirror primary and secondary disk subsystems are configured with the same Logical Subsystem number (LSS) and Channel Connection Address (CCA) pairs. That is the PPRC primary and secondary devices have the same LSS and CCA in the local and remote storage controllers. These configurations are believed to be common as most clients configure Metro Mirror primary and secondary disk subsystems identically. An asymmetrical configuration has logical LSS and CCA numbers different between the local and remote sites.
- STAT011_PRESERVE_INDEX=
-
- YES
- YES If CVAF returns a STAT011 error to its caller, the VTOC Index will not be disabled.
If STAT011_PRESERVE_INDEX=YES is specified, an IEA253I STAT011 ERROR WILL PRESERVE THE VTOC INDEX is logged.
If STAT011_PRESERVE_INDEX=YES and RETRY(STAT011) are both coded in DEVSUP member, DADSM allocation performs the following actions without disabling the VTOC index:
Internally detects the failure associated with IEC608I message followed by an SVC dump of DADSM with diagnostic codes: DIAG=0820040B, 0853040B, 0854040B or 0855040B which is the result of CVAF setting status x0B(STAT011) when it uses an orphan Format-3 DSCB as a free Format-0 DSCB. If this is detected, the dump is not being issued until later during VTOC validation.
A new VTOC validation function will be used to determine the status of the orphan Format-3 DSCBs and other VTOC conditions ('VTOC NOT CONVERTED', 'INCORRECT EXTENTS' or DUPLICATE F1 WITH SAME F3'). The message below will be displayed to indicate that validation is entered. The validation does not reclaim any orphan Format-3 DSCB(s).
IEC604I VTOC VALIDATE ENTERED ON DEVICE xxxx,volser ,----,DEVMAN
New message IEC618_ will be displayed for any errors about the DSCBs. If there are other VTOC errors, IEC602I message may be issued.
IEC618I ORPHAN FMT-3 DSCB,DEV=uuuu,volser,yy, (DSCBNO=xxxxxxxxx, DSCB=cccchhhrr)
IEC618E INCORRECT EXTENTS IN DSCB=cccchhhhrr, DSN=Up to 44-byte datasetname
IEC618E SAME F3 WITH DUPLICATE F1=cccchhhhrr, DSN=Up to 44-byte datasetname
IEC618E INCORRECT F3s COUNT IN F9=cccchhhhrr, DSN=Up to 44-byte datasetname
IEC602I VTOC NOT CONVERTED ON uuuu,volser, 0,(EXTENT=CCHHCCHH,DSCB=CCCCHHHHRR-CCCCHHHHRR)
Take a DEVMAN SVC dump of the current indexed VTOC. The dump will show as below.
DUMP TITLE=VTOC VALIDATTION,VOLSER=volser, REASON=IEC6xxx,ERROR= error-message-text The IEC6xxI reason will be IEC618I, IEC618E, or IEC602I.
The error-message-text will be one of the following reasons:- ORPHAN FMT3 CHAIN
- ORPHAN FMT-3 DSCB
- INCORRECT EXTENTS IN DSCB
- ORPHAN F3 W/ INVALID DSCB
- SAME F3 WITH DUPLICATE F1
- INCORRECT F3s COUNT IN F9
- OTHER VTOC ERRORS
If single non-chained orphan Format-3 DSCB is the only type of error indicated by 'ORPHAN FMT-3 DSCB' in IEC618I, and if RETRY(STAT011) is activated in the system, the system will retry the allocation to use up one or at most two orphan format-3 dscbs, and will not disable the VTOC index since STAT011_PRESERVE_INDEX=YES. If RETRY(STAT011) is not activated, the system will not retry to use up the orphan format-3 dscb. However, the failure will still not disable the VTOC index.
In addition to detecting the single orphan Format-3 DSCB condition above, if another VTOC error (as shown in IEC618_ and IEC602I with a different reason text i.e 'ORPHAN FMT3 CHAIN', or 'INCORRECT EXTENTS IN DSCB'), the VTOC index will not be disabled. The failure will be issued with CVAF status code STAT011 regardless RETRY(STAT011) is activated or not.
If the retry is not successful, the message below will be issued to confirm the error as it always does today. IEC603I VTOC ERRORS MAY EXIST ON uuuu,volser, 8
- NO
- If CVAF returns a STAT011 error to its caller, the VTOC Index may be disabled. This is the
system default keyword.
If STAT011_PRESERVE_INDEX=NO is specified, an IEA253I STAT011 ERROR WILL DISABLE THE VTOC INDEX is logged. If STAT011_PRESERVE_INDEX=NO is activated, DADSM allocation performs the following actions and disables the VTOC index or converts it to OSVTOC:
Internally detects the failure associated with IEC608I message followed by an SVC dump of DADSM with diagnostic codes: DIAG=0820040B, 0853040B, 0854040B or 0855040B which is the result of CVAF setting status x0B(STAT011) when it uses an orphan Format-3 DSCB as a free Format-0 DSCB. If this is detected, the dump is not being issued until validation processing.
A new VTOC validation function will be used to determine the status of the orphan Format-3 DSCBs and other VTOC conditions. The message below will be displayed to indicate that validation is entered.
IEC604I VTOC VALIDATE ENTERED ON DEVICE xxxx,volser,----,DEVMAN
New message IEC618_ will be displayed for any errors about the DSCBs. If there are other VTOC errors, a IEC602I message may be issued.
IEC618I ORPHAN FMT-3 DSCB,DEV=uuuu,volser,yy, (DSCBNO=xxxxxxxxx, DSCB=cccchhhrr)
IEC618E ORPHAN FMT3 CHAIN,DEV=uuuu,volser,yy, (DSCBNO=xxxxxxxxx, DSCB=cccchhhrr)
IEC618E INCORRECT EXTENTS IN DSCB=cccchhhhrr, DSN=Up to 44-byte datasetname
IEC618E SAME F3 WITH DUPLICATE F1=cccchhhhrr, DSN=Up to 44-byte datasetname
IEC618E INCORRECT F3s COUNT IN F9=cccchhhhrr, DSN=Up to 44-byte datasetname
IEC602I VTOC NOT CONVERTED ON uuuu,volser, 0, (EXTENT=CCHHCCHH,DSCB=CCCCHHHHRR-CCCCHHHHRR)
Take a DEVMAN SVC dump of the current indexed VTOC. The dump will show as below.
DUMP TITLE=VTOC VALIDATTION,VOLSER=volser, REASON=IEC6xxx,ERROR= error-message-text The IEC6xxI reason will be IEC618I, IEC618E, or IEC602I.
The error-message-text will be one of the following reasons:- ORPHAN FMT3 CHAIN
- ORPHAN FMT-3 DSCB
- INCORRECT EXTENTS IN DSCB
- ORPHAN F3 W/ INVALID DSCB
- SAME F3 WITH DUPLICATE F1
- INCORRECT F3s COUNT IN F9
- OTHER VTOC ERRORS
If single non-chained orphan Format-3 DSCB is the only type of errors indicated by 'ORPHAN FMT-3 DSCB' in IEC618I, and if RETRY(STAT011) is activated in the system, the system will retry the allocation to use up one or at most two orphan format-3 dscbs. and it will not disable the index if the allocation is successful. If RETRY(STAT011) is not activated, the system will not retry to use up the orphan format-3 dscb. However, any VTOC failure will disable the VTOC index since STAT011_PRESERVE_INDEX=NO is used.
In addition to detecting the single orphan Format-3 DSCBs (only 'ORPHAN FMT3 CHAIN' in IEC618I message) condition, if another VTOC error is detected as shown in IEC618E or IEC602I with a different reason text, the VTOC index will be disabled, and the system will call the CONVERT routine to convert to non-indexed VTOC(aka. OSVTOC).
An IEC608I message with reason code 24 will be issued as below. IEC608I DADSM FUNCTION DISABLED THE VTOC devn,volser, 24, CCHHR
Issue an IEC604I message below before converting the disabled-index VTOC to non-indexed VTOC(OSVTOC) device.
IEC604I VTOC CONVERT ROUTINE ENTERED ON devn,volser, DI-O,DEVMAN
The CONVERT(IGG0425P) routine will attempt to reclaim the orphan DSCBs, and fix any space errors if possible.
The system will restart the allocation one more time on the non-indexed VTOC device.
Notice that once the disabled indexed VTOC has been converted to OSVTOC, performance may be affected by a large VTOC or the increasing number data sets over time. If that is the case, use ICKDSF program to convert the VTOC back to an indexed VTOC with the ICKDSF BUILDIX command: BUILDIX DDNAME(DDVOL) IX If the keyword is not specified, no message is logged.
Default: NOAll references to RETRY(STAT011) will be updated as below.
RETRY(STAT011)
If the keyword is specified in the DEVSUPxx parmlib member DEVSUPxx, and SET DEVSUP=xx command is issued to activate the option, the following message will be issued.
IEA253I RETRY ALLOCATION FOR ORPHAN DSCB ERROR(STAT011) If the keyword is not specified, there will be no IEA253I message after SET DEVSUP=xx command is issued. If the keyword is activated, DADSM allocation will perform the following actions:
Detect the failure with IEC608I message followed by an SVC DADSM dump with diagnostic codes: DIAG=0820040B, 0853040B, 0854040B or 0855040B which is a result of CVAF setting status x0B(STAT011).
Take an DEVMAN SVC dump of the disabled-index VTOC and issue IEC608I message with reason code 24 as below.
IEC608I DADSM FUNCTION DISABLED THE VTOC devn,volser, 24,CCHHR
Issue IEC604I message below before converting the disabled- index VTOC to non-indexed VTOC(OSVTOC) device.
IEC604I VTOC CONVERT ROUTINE ENTERED ON devn,volser, DI-O,DEVMAN
Restart the allocation one more time on the non-indexed VTOC device. Notice that the disabled indexed VTOC has been converted to OSVTOC. The performance may affect slightly if the number data sets is increased significantly over time. If that is the case, use ICKDSF program to convert the VTOC back to an indexed VTOC with the ICKDSF BUILDIX command: BUILDIX DDNAME(DDVOL) IX Refer to STAT011_PRESERVE_INDEX keyword to see how the system behaves when RETRY(STAT011) keyword is used with STAT011_PRESERVE_INDEX keyword.
This table provides a summary of how these two keywords are combined together in the system.STAT011_PRESERVE_INDEX=NO STAT011_PRESERVE_INDEX=YES Without RETRY(STAT011) active in the system - This is existing behavior which is also the default behavior. - Detect orphan DSCB - Take DEVMAN DUMP
WILL NOT attempt to retry on orphan DSCBs.
Will fail and not disable the index.
With RETRY (STAT011) active in the system - Detect orphan DSCB - Take DEVMAN DUMP
- Retry to use the orphan DSCB if possible.
- If failed, it will disable the index.
- Convert to OSVTOC retry allocation once more.
- Detect orphan DSCB - Take DEVMAN DUMP
- Retry to use the orphan DSCBs if possible.
- If failed, it will not disable index.
- Index is preserved and not converted to OSVTOC.
- TAPEAUTHDSN=
- NO
- Indicates that OPEN processing to issue RACROUTEs based on the options set in RACF® such as SETROPTS TAPEDSN and SETROPTS CLASSACT(TAPEVOL).
- YES
- Enables tape authorization checks in the DATASET class but without
DSTYPE=T. All tape data set names created are RACF-protected.
DSTYPE=T indicates to RACF that the check is for data set on a tape volume and that special RACF tape data set and a tape volume processing is to be performed. Without DSTYPE=T RACF authorization checking considers only profiles in the DATASET class.
The system uses the data set name that is specified in the allocation or JCL to check your authorization to read or write the specified file.
In addition, the system determines the RACF erase-on-scratch setting from the RACF profile and passes it to your tape management system.
Use this option only when you have a tape management system, such as DFSMSrmm, installed and actively checking that the 44 character data set name that is specified by the user matches the data set name on tape. Without a tape management system, tape data set open processing can only validate the last 17 characters of the data set name against the tape volume labels.
When you request bypass label processing (BLP) and the mounted volume uses standard labels, OPEN issues the authorization check that the user is authorized to use BLP. This processing uses the existing ICHBLP resource in the RACF FACILITY class. When you specify TAPEAUTHDSN=YES only, it replaces the check that RACF makes as part of tape volume authorization checking.
Default: NO- TAPEAUTHF1=
- NO
- Disables additional tape authorization checks in the DATASET class for existing files on the same tape volume when any other file on the tape volume is opened. The default value is NO.
- YES
- Enables additional tape authorization checks in the DATASET class
for existing files on the same tape volume when any other file on
the tape volume is opened. This function depends on the tape management
system returning the 44 character data set name and data set sequence
number to OPEN/EOV through the IFGTEP during the Volume Mount exit
Volume Security function; if no data set name is returned by the tape
management system, processing is as if this keyword had not been specified.
Although intended to enable an additional authorization check for the first data set when any other data set on the tape volume is opened, the implementation allows your tape management system to request one or more additional authorization checks when any data set on a tape volume is opened. Each additional data set name and data set sequence number returned results in an additional RACROUTE. Do not use this function unless you have a tape management system and it can return a data set name and data set sequence number. A data set sequence number is the label number that is normally specified in the JCL LABEL keyword and stored in the catalog.
When TAPEAUTHDSN=YES is in use, any additional RACROUTE matches that issued for TAPEAUTHDSN except for the data set name and data set sequence number. Otherwise TAPEAUTHF1 uses a RACROUTE that matches that used for SETROPTS TAPEDSN. When neither TAPEAUTHDSN nor SETROPTS TAPEDSN is in use, TAPEAUTHF1 support is not provided.
- TAPEAUTHRC4=
- This applies to authorization checks in the DATASET class, and
applies only to the results of TAPEAUTHDSN=YES and TAPEAUTHF1=YES
processing.
- ALLOW
- Allows accessing of data sets that are not protected by a security
profile.
RC4
refers to the return code value of 4 returned from SAF as a result of the RACROUTE issued by OPEN/CLOSE/EOV. A return code of 4 in general means that the resource is not protected. - FAIL
- Denies accessing of data sets that are not protected by a security profile. TAPEAUTHRC4=FAIL and TAPEAUTHDSN=YES together ensure that all tape data set names created including temporary names generated by the tape system are RACF-protected.
Default: FAILUse this keyword to control PROTECTALL processing for tape data sets. This applies to the results of RACROUTE processing when both TAPEAUTHDSN=YES and when TAPEAUTHF1=YES are specified.
- TAPEAUTHRC8=
- Provides a managed and controlled implementation of tape authorization
checks in the DATASET class, and applies only to the results of TAPEAUTHDSN=YES
and TAPEAUTHF1=YES processing. This keyword is provided as an aid
to the implementation of TAPEAUTHDSN and TAPEAUTHF1.
- FAIL
- Denies accessing of data sets that typically cannot be accessed.
- WARN
- Allows accessing of data sets that typically cannot be accessed. RACF issues an ICH408I message to indicate why access is not allowed; however OPEN/EOV allows access.
Default: FAIL - TAPEBLKSZLIM=
- Specifies the default block size limit for the system to use when a user omits the block size
limit on a DD statement for a tape data set and the data class does not supply one. The system
stores this value in the DFA (data facilities area), for use by the system and by application
programs. See z/OS DFSMSdfp Advanced Services. The system uses this value only in cases when all of the following statements
are true.
- An application program uses the large block interface (LBI) of BSAM or QSAM to open a tape data set for output without DISP=MOD. Check the information for the program; if its maximum block size is 32760 or less, or it cannot write to tape, the program probably does not use the LBI.
- The BLKSIZE (block size) value is omitted from all sources.
- The DD statement or dynamic allocation equivalent and the data class do not specify a BLKSZLIM value.
Restriction: DFSMSdss only supports BLKSZLIM of 65,520 and higher.An application program that uses EXCP can take this value from the DFA.
If you code K, M, or G at the end of the number, the system multiplies the number by 1024, 1,048,576 or 1,073,741,824 respectively. The minimum values are 32760 when specified in bytes, 32 K when specified in kilobytes, 1 M when specified in megabytes, and 1G when specified in gigabytes. The maximum values are 2147483648, 2097152 K, 2048 M, and 2 G. These maximum block size values are much larger than the system supports for BLKSIZE. Coding a large value, however, allows the system to choose the largest optimal block size for the device.
The default for this parameter is 32760. Do not code a value that exceeds 32760 in DEVSUPxx if both of the following statements are true:- Your system has a job that writes on tape using the large block interface and the job does not supply a value for BLKSIZE or BLKSZLIM. Programs that use the large block interface include IEBGENER, ICEGENER, DFSORT, and programs that are compiled with COBOL for OS/390® and VM Version 2 Release 2.
- The tapes with a large block size might be read on a level of MVS that precedes OS/390 Version 2 Release 10 or might be read on another type of system that does not support such large blocks. OS/400® supports large blocks.
- TAPE_MULTI_VOLUME_ANOMALY=
- Specifies how the system handles any multivolume tape label anomaly condition that is not yet
resolved after the Label Anomaly exit is called. This keyword is processed at IPL time, but can be
changed by the operator using SET DEVSUP=xx.
If the Label Anomaly exit sets return code 12, it is honored and in all cases it fails the request, overriding the DEVSUPxx setting.
- ALLOW
- Use this setting to allow applications to process multi-volume tape data sets even when the volume set is incomplete or in the wrong sequence.
- FAIL
- Use this setting to prevent applications from processing multi-volume tape data sets when the volume set is incomplete or in the wrong sequence.
Default: ALLOW.When a request is failed, either by the Label Anomaly exit return code 12, or by the FAIL option, the System Completion Codes are: 413-58 (OPEN RDBK), 413-5C (OPEN FIRST), 637-B4 (EOV OUTSEQ), and 637-B8 (EOV LAST).
DFSMSrmm attempts to recover from errors that are noted in the label anomaly exit using the volume sequence information that is recorded in the DFSMSrmm control data set (CDS). Based on information that is returned by DFSMSrmm, OPEN and EOV processing attempts to resolve the error by updating the volume list in the job file control block (JFCB) and any JFCB extensions.
Tape users can bypass the system multivolume tape label anomaly processing by specifying OPTCD=B in the JCL. For more information about for the considerations using OPTCD=B, see the topic Determining volume switch in these references:The tape application can optionally recover from a tape label anomaly failure by providing a DCB abend exit for the applications’ DCB. When the application DCB abend exit requests recovery, the missing or out of sequence volume condition is ignored.
- VOLNSNS=
-
- NO
- Specifies that tape cartridges written at track capacities that the drive is not capable of reading (for example, a 36-track cartridge on a D/T3480, or a 256-track cartridge on a D/T3590 Model B1x), are not allowed to be relabeled. Attempts to relabel the cartridges are rejected when RACF protection for tape volumes is active. If no installation default for the VOLID facility VOLNSNS is provided by using the DEVSUPxx member, the system assumes VOLNSNS=NO.
- YES
- Specifies that tape cartridges written at track capacities that the drive is not capable of reading (for example, a 36-track cartridge on a D/T3480, or a 256-track cartridge on a D/T3590 Model B1x), be relabeled at the device-capable track capacity by the OPEN or EOV label editor routines. This relabel editor option is permitted only if the user is RACF-authorized to the volume. The volume serial number that is passed to RACF is obtained from the VOLID mark written on the cartridge by the device, and placed in the sense data.