Power requirements for frames
A description of the power requirements for frames in the TS3500 tape library.
Table 1 lists the electrical characteristics for the TS3500 tape library frame models.
Electrical characteristic | Rating2 | |
---|---|---|
TS3500 tape library | Models L22, D22, L32, D32, L52, D52 | |
Nameplate electrical limits1 | 200–240 V ac, 8.0 A, 50–60 Hz, 1.6 kVA, single phase | 100–127 V ac, 12.0 A, 50–60 Hz, 1.2 kVA, single phase |
200–240 V ac, 8.0 A, 50–60 Hz, 1.6 kVA, single phase | ||
Inrush current | 150 A @ 200–240 V ac (peak for 1/2 cycle) | 100 A @ 120 V ac, 200 A @ 240 V ac (peak for 1/2 cycle) |
Leakage current | 1 mA | 8 mA maximum with 12 drive power supplies installed |
Notes:
|
Table 2 lists the power consumption of the TS3500 tape library models, power consuming features, and drive canisters.
Models | Power consumption (Watts) | ||
Off7 | Idle | Max. continuous (not peak) | |
L32, L22, L52 | 7 | 200 | 260 |
D32, D22, D522 | 7 | 200 | 200 |
L23, L531 | 13 | 142 | 202 |
D23, D531,2 | 13 | 103 | 103 |
S24, S543 | 0 | 5 | 5 |
HA14 | 0 | 24 | 85 |
SC1 (FC 1850 and 1851)8 | 0 | 11 | 20 |
Feature Codes | |||
FC 1503 and 1504 (Drive mounting kit for xx2 models)5 | 0 | 15 | 20 |
FC 1513, 1514, and 1515 (Drive mounting kit for xx3 models)5 |
0 | 4 | 7 |
FC 1950 PDU | 5 | 17 | 17 |
FC 4872 TS7700 backend 4 Gb switches (2x) |
0 | 113 | 113 |
FC 4875 TS7700 backend 8 Gb switches (2x) |
0 | 86 | 86 |
Tape drives6 | |||
TS1120 (3592 Models E05 and J1A) | 0 | 27 | 42 |
TS1130 (3592 Model E06) | 0 | 17 | 46 |
TS1140 (3592 Model E07) | 0 | 23 | 50 |
TS1150 (3592 Model E08) | 0 | 23 | 47 |
TS1155 (3592 Model 55G) | 0 | 23 | 47 |
TS1160 (3592 Model 60G) | 0 | 47 | 61 |
TS1030 (LTO 3588 F3B) | 0 | 20 | 34 |
TS1040 (LTO 3588 F4A) | 0 | 18 | 36 |
TS1050 (LTO 3588 F5A) | 0 | 12 | 28 |
TS1060 (LTO 3588 F6A) | 0 | 9 | 32 |
TS1070 (LTO 3588 F7A) | 0 | 16 | 34 |
TS1080 (LTO 3588 F8A) | 0 | 16 | 34 |
Notes:
|
In order to calculate the total power consumption (in watts) of a particular library configuration, multiply the quantity of each power consuming item in the configuration by the corresponding value in Table 2 and calculate the total. In order to calculate the total cooling required by the library (in Btu/hr), multiply the total power in watts by 3.4. To convert Btu/hr to kBtu/hr, divide your result by 1000.
Table 3 provides a sample calculation of total power and cooling requirements for a TS3500 tape library configuration consisting of one L23 with ten TS1130 tape drives and mounting kits, four D23 models each containing six TS1130 tape drives and mounting kits, one D23 with no drives or enhanced FCA feature (FC 1451), two S24 models, and one HA1 model.
This model | With this feature code | And these tape drives | Quantity | Power (Watts) | ||
Off | Idle | Max. continuous | ||||
L23 | 15151 | TS1130 | 1 | 13 | 142 | 202 |
10 | 0 | 40 | 70 | |||
10 | 0 | 170 | 460 | |||
D23 (with FC 14512) |
1515 | TS1130 | 4 | 52 | 412 | 412 |
24 | 0 | 96 | 168 | |||
24 | 0 | 408 | 1104 | |||
D23 (without FC 1451) |
N/A | N/A | 1 | 0 | 0 | 0 |
S24 | N/A | N/A | 2 | 0 | 10 | 10 |
HA1 | N/A | N/A | 1 | 0 | 24 | 85 |
Total power consumption: | 65 | 1302 | 2511 | |||
Total cooling requirement (kBtu/hr): | 0.2 | 4.4 | 8.5 | |||
Notes:
|
Library power consumption is dynamic and usage dependent. Short peaks might exceed the maximum continuous power values. Typical average power consumption is lower than the calculated maximum continuous value because all drives are not likely to be active simultaneously.