HSCL3xxx error codes

These error codes can be displayed in a window that is displayed on the HMC screen during system configuration and operations.
Back to HSCL error codes page
HSCL3xxx error codes Message Recovery action
HSCL3006 The LED operation failed. Refer to the HMC Operations Guide for more details. {0}
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3060 The following managed frames failed to initialize: {0}. If the error persists, contact your software service representative.
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3070 The Frame lock action failed. Try the operation again.
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3071 The Frame Guided Maintenance operation failed. Try the operation again. Try the operation again. If the problem persists, contact your hardware representative.
HSCL3072 The Frame FRU deactivation operation failed. Try the operation again. Try the operation again. If the problem persists, contact your hardware representative.
HSCL3073 The Frame FRU activation operation failed. Try the operation again. Try the operation again. If the problem persists, contact your hardware representative.
HSCL3074 The frame host information was not saved. Ensure the Hardware Management Console has enough disk space and the correct file permission and try the operation again. Ensure that the /opt/hsc/data directory contains enough disk space so that the HMC can save the frame host information when needed.
HSCL3075 The frame host information that was found is not valid. Check the host information you provided and try the operation again. Check the frame host information that was entered into the application program to ensure the host name, password, and frame bulk power controller (BPC) internal identification are valid.
HSCL3076 An error has occurred while attempting the bulk power assembly connection operation. Retry the operation. If the problem persists, contact your service representative.
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3077 This operation is not allowed in the frame's current state. In order for this operation to be performed, at least one bulk power assembly (BPA) must be in the Standby state.
  1. Make sure that at least one bulk power assembly is in the Standby state, and try the operation again.
  2. If the problem persists, contact your hardware representative.
HSCL3078 The request to power on the drawer or planar for the frame failed. Try the request again. Try the request again. If the problem persists, contact your service provider.
HSCL3079 The request to add a drawer to the frame failed. Try the request again. Try the request again. If the problem persists, contact your service provider.
HSCL307A This operation cannot be performed because the HMC is not connected to side {0} of the bulk power assembly (BPA). Check the connection and try the operation again.
  1. Check the connection.
  2. Try the operation again.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL3080 The request to remove a planar from the frame failed. Try the request again. Try the request again. If the problem persists, contact your next level of support or your service provider.
HSCL3081 The request to remove a drawer from the frame failed. Try the request again. Try the request again. If the problem persists, contact your next level of support or your service provider.
HSCL3082 The request to send the frame IP information to the managed system has failed. Try the request again. If the problem persists, contact your next level of support or your service provider.
HSCL3083 This operation is not allowed when the cage is powered on. Before this operation can be performed, all the cages must be powered off.  
HSCL3084 This operation is not allowed when the BPA is in any of the following states: Incomplete, No Connection, or Not Available. After you have established a connection from the HMC to the BPA, and have entered a valid HMC access password, try the operation again.  
HSCL3200 Unknown lock error. Contact your next level of support or your service provider.
HSCL3201 Lock type not valid.
  1. Restart the HMC.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3202 Failed to acquire lock because of timeout.
  1. Restart the HMC.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3203 Nested lock type requested not valid.
  1. Restart the HMC.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3204 Lock not held.
  1. Restart the HMC.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3205 The managed system is busy, try the operation again later. The managed system is busy doing another action. Wait and then retry the action.
HSCL3351 Code update process is not allowed by the HMC. Check the code update status to verify the code update owner.
  1. Check the code update status to verify the code update owner.
  2. Retry the operation if HMC is the code update owner.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL3352 Code update is already in progress by another HMC or by the firmware. Verify that no other code update is in progress and retry the operation.
  1. Verify that no other code update operation is in progress and retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3353 Code update is not allowed to the specified side. Check the current flash side.
  1. Rebuild the managed operation. For details, see Updating managed system or frame information.
  2. Check the power-on side from the managed system property panel and ensure you are not performing code update to the power-on side and then retry the operation.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL3354 Code update is already in progress from this HMC. Ensure that no code update operation is in progress on the HMC before retrying the operation.
  1. Ensure that no code update operation is in progress on the HMC before retrying the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3355 The code update operation failed with return code {0}.
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3356 The code update is not in progress by this HMC. The start code update task should have been performed prior to code update complete by this HMC.
  1. Ensure that the start code update task has been performed.
  2. Retry the operation.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL3357 The operation failed since another commit or long running code update is in progress.
  1. Ensure that no other code update operation is in progress.
  2. Retry the operation.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL3358 The delete LID operation is not allowed when a write LID is in progress.
  1. Ensure that no other code update operation is in progress.
  2. Retry the operation.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL3359 The code update operation failed since an invalid LID ID was specified.
  1. Check the LID file ID and retry the operation with a valid LID file ID.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3360 Error accessing the flash.
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3361 An unknown error occurred during code update operation. Retry the operation.
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3362 An unknown error occurred during reboot service processor. Retry the operation.
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3363 The size of the LID number array is not the same as the Filename array. Ensure every LID number has a corresponding filename.
  1. Ensure every LID number has a corresponding filename and retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3364 The read LID operation failed: {0}.
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3365 Error: The following file(s) already exist(s): {0}.
  1. Ensure the files to read in the LID files do not exists and retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3367 The input parameter arrays should all be of the same length. Check the lengths and retry the operation.
  1. Ensure the lengths of the input parameters are the same and retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3368 The Max write block size for the start code update did not get set. Retry the operation.
  1. Retry the operation for the LID files that failed.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3370 The deletion of the following LID(s) failed: {0}.
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3371 The write LID operation failed: {0}.
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3372 The following LID filenames are not files: {0}
  1. Ensure the LID files exist and retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3373 The following LID files are empty: {0}
  1. Ensure that the LID files are valid and retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3374 The following LID files do not exists: {0}
  1. Ensure the LID files exist and retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3376 Invalid value returned from the service processor to indicate whether service partition firmware code LID updates are enabled or disabled.
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3377 The start code update operation failed since an invalid component to update was specified. Retry the operation with the a valid firmware component to update.
  1. Retry the operation with a valid firmware component to update.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3378 The start code update operation failed since the managed system is not in the valid state. Check the state of the managed system and retry the operation.
  1. Check the state of the managed system and retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3379 There is a permanent error in flash, retry the operation and if the problem persists contact support.
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3380 The Code Update operation failed since the managed system is not in the Power Off, Operating, or Standby state. Check the managed system's state and retry the operation.
  1. Check the state of the managed system and retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3381 The Complete Code Update operation failed since an invalid completion type was specified. Retry the operation with a valid completion type.
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3382 The Code Update is not in progress. The start code update operation needs to be performed before the Complete Code Update operation.
  1. Ensure the start code update operation is performed first.
  2. Retry the operation.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL3383 One or more LIDs are invalid in the primary LID list.
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3384 For the partial read, the specified length was not read since the end of file flag was reached.
  1. Retry the operation with a valid length to be read.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3385 Error: The following file(s) specified an invalid data for the Special LID Designator or the code update side: {0}
  1. Retry the operation with valid special LID designator or the code update side.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3386 The read partial/special LID operation failed, since writing to the file on the HMC got an error. Check the log for the error and retry the operation.
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3387 An unknown error occurred during the open of firmware files. Retry the operation.
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3388 The following fileid-subid specified an invalid open type: {0}
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3389 The following fileid-subid specified an invalid Force Flag: {0}
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3390 Error: The following files got an exception while trying to open the firmware file: {0}
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3391 The open firmware file operation failed: {0}
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3392 An unknown error occurred during the write operation of firmware files. Retry the operation.
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3393 An unknown error occurred during the close of firmware files. Retry the operation.
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3394 An unknown error occurred during the get firmware status update operation. Retry the operation.
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3395 An unknown error occurred during the start firmware update operation. Retry the operation.
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3396 Failed to delete the partition with ID {0} since it is the service partition.
  1. Ensure the partition is not the service partition.
  2. Rebuild the managed system. For details, see Updating managed system or frame information.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL3397 The secondary service processor is not available for the managed system.
  1. Check the FSP configuration and make sure that the service processor is installed and available for failover.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3398 The code update service processor lock is already taken. Check that no other code update operation is running and retry the operation.
  1. Check that no other code update operation is in progress and retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3399 The code update service processor lock is not taken. Ensure the lock is taken before trying to release the code update service processor lock.
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3400 The service processor target that was specified is not valid. Verify the service processor target name and try the request again.
  1. Rebuild the managed frame. For details, see Updating managed system or frame information.
  2. Try the task again.
  3. If the problem persists, contact your service provider.
HSCL3401 The get power domain operation failed. Retry the operation.
  1. The I/O concurrent maintenance command failed. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3402 The get power domain power state operation failed. Retry the operation.
  1. The I/O concurrent maintenance command failed. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3403 The set service lock operation failed. Retry the operation.
  1. The I/O concurrent maintenance command failed. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3404 The reset service lock operation failed. Retry the operation.
  1. The I/O concurrent maintenance command failed. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3405 The FRU level activate operation failed. Retry the operation.
  1. The I/O concurrent maintenance command failed. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3406 The FRU level deactivate operation failed. Retry the operation.
  1. The I/O concurrent maintenance command failed. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3407 The vary off power domain platform operation failed. Retry the operation.
  1. The I/O concurrent maintenance command failed. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3408 The vary off power domain platform operation failed. Retry the operation.
  1. The I/O concurrent maintenance command failed. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3409 The vary on power domain platform operation failed. Retry the operation.
  1. The I/O concurrent maintenance command failed. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3410 The vary off power domain partition operation failed. Retry the operation.
  1. The I/O concurrent maintenance command failed. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3411 The vary off power domain partition operation failed. Retry the operation.
  1. The I/O concurrent maintenance command failed. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3412 The vary on power domain partition operation failed. Retry the operation.
  1. The I/O concurrent maintenance command failed. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3413 No Partitions are defined for the managed system. Check the user interface to see if partitions are defined and then retry the operation.
  1. Rebuild the managed system. For details, see Updating managed system or frame information.
  2. Retry the task.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL3414 The start I/O concurrent maintenance operation failed. Retry the operation.
  1. The I/O concurrent maintenance command failed. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3415 The I/O concurrent maintenance operation failed. Retry the operation.
  1. The I/O concurrent maintenance command failed. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3416 The get configuration ID operation failed. Retry the operation.
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3417 The set configuration ID operation failed. Retry the operation.
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3418 The get IO unit configuration ID and MTMS operation failed. Retry the operation.
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3419 The set IO unit MTMS operation failed. Retry the operation.
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3420 The set IO unit configuration ID operation failed. Retry the operation.
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3421 This operation is not allowed in the managed system's current state. Check the state of the managed system and retry the operation.
  1. Check the state of the managed system and retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3422 This operation cannot be completed because a conflicting concurrent maintenance operation is already in progress. Ensure that the other operation has completed and then retry the operation.
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3423 Invalid data {0} was specified for this operation. Check the data and retry the operation.
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3424 The I/O concurrent maintenance operation failed with return code: {0}.
  1. Retry the operation.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3431 The command display service effect failed {%0}. Please retry the operation again.  
HSCL3432 The system level deactivation failed {%0}. Please retry the operation.  
HSCL3433 The system level deactivation failed {%0}. Please retry the operation.  
HSCL3437 The managed system does not have Concurrent Maintenance capability. Please upgrade the firmware and retry the operation.
  1. Upgrade the firmware that supports Platform Hardware Concurrent Maintenance and retry the operation. For details, see Obtaining firmware updates.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3438 The managed system does not have PHYP Concurrent Maintenance capability. Please upgrade the firmware and retry the operation.
  1. Upgrade the firmware that supports Platform Hardware Concurrent Maintenance and retry the operation. For details, see Obtaining firmware updates.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3439 Query FSP CM Service Lock failed. Please retry the operation.
  1. Please retry the operation
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3500 The function completed successfully.  
HSCL3501 The operation failed because of a non-trivial reason.
  1. Restart the HMC and retry the task.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3503 Input error: The specified value is out of range or undefined. Contact your next level of support or your service provider.
HSCL3504 An invalid input file or an error has occurred during an operation on the specified file.
  1. Restart the system.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3505 An error occurred while contacting the access control system. Retry the operation.
  1. Restart the system.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL350A Invalid input parameter(s).
  1. Check the input and try the task again.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL350B The user does not have the appropriate authority.
  1. Try the task again.
  2. Restart the system.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL350C Input error: An invalid operation has been specified.
  1. Check the input and try the task again.
  2. Restart the system.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL350D Input error: An invalid user ID has been specified.
  1. Check the input and try the task again.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL350E Input error: An invalid task has been specified.
  1. Check the input and try the task again.
  2. Restart the system.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL350F Input error: The input resource is not valid or conflicts with the role in the operation.
  1. Check the input and try the task again.
  2. Reboot the system.
  3. If the problem persists, contact your next level of support or your service provider.
  1. Check the input and try the task again.
  2. Restart the system.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL3510 Input error: An invalid role or parent role has been specified.
  1. Check the input and try the task again.
  2. If the problem persists, contact your next level of support or your service
HSCL3511 Input error: An invalid subsystem has been specified.
  1. Check the input and try the task again.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3512 Input error: An invalid option has been specified.
  1. Check the input and try the task again.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL3513 Input error: An invalid managed resource role name has been specified.
  1. Check the input and try the task again.
  2. Restart the HMC.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL3514 The role specified already exists. A duplicate role name has been specified in the operation. Select a different name.
HSCL3532 An unknown error, such as an exception, has occurred during the operation.
  1. Try the task again.
  2. Restart the HMC.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL3533 Invalid operation. The input role is a system predefined role. The operation is not allowed.
HSCL3534 An invalid assignment has been specified. The resource type of the assignment is invalid or conflicts with the user's role. The resource type specified in the assignment is not valid or conflicts with the user role. Give the user a different assignment or role and retry the operation.
HSCL3563 The function specified is not available in the current release.