Installing the file modules
Install the file modules in the rack following the safety guidelines.
About this task
To install each file module in the rack, follow these instructions.
Procedure
- Pull the slide rails forward 1 until
they click, two times, into place as shown in Figure 1. Carefully
lift the file module and
tilt it into position over the slide rails so that the rear nail heads 2 on
the device line up with the slide rails. Slide the file module down
until the rear nail heads slip into the two rear slots, and then slowly
lower the front of the file module 3 until
the other nail heads slip into the other slots on the slide rails.
See Figure 1.Figure 1. Installing the file module on the slide rails.
- Lift the locking levers 1 on
the slide rails and push the file module 2 all
the way into the rack until it clicks into place. Refer
to Figure 2.Figure 2. Sliding the file module into the rack.
- Install the cable management
support bar on the left-rear side of the node, as shown in Figure 3.
- Connect one end of the support bar to the same slide rail to which you plan to attach the cable management arm assembly.
- Swing the other end of the support bar toward the rack.
Figure 3. Installing the cable-management support bar - Connect the other end of the support
bar to the stop bracket, as shown in Figure 4. Figure 4. Connecting the cable management support bar to the stop bracket
- Connect the stop bracket to
the slide rail, as shown in Figure 5.
- The capital letters I and O are printed on cable management arm pins to identify the inside and outside pins.
- Install the stop bracket (with capital letter O) on the unattached end of the support bar.
- Verify that the support bar is securely installed.
Figure 5. Connecting the stop bracket to the slide rail - Install the cable
management arm as shown in Figure 6.
- Place the cable management arm on the support bar.
- Pull out both the inside and the outside pins of the cable management arm.
- Slide the cable management arm tabs into both the inside and the outside slots of the slide rail.
- Push the tabs until they snap into place.
Figure 6. Installing the cable management arm - Close the stop bracket
as shown in Figure 7.
- Open the stop bracket, which makes rotating the cable management arm on and off the support bar easier.
- Push the tabs above and below the stop bracket to close it.
Figure 7. Closing the stop bracket - Connect and route the cables as
shown in Figure 8.
- Connect the power cords and other cables to the rear of the node.
- Route the cables and power cords on the cable management arm and secure them with cable ties or hook-and-loop fasteners.
Note:- The location of the cable straps can vary in different systems.
- Use the cable straps that are provided on the rear of the system to retain the cables and prevent them from sagging.
Figure 8. Connecting and routing the cables - Secure the cables with the hook-and-loop
fastener strap, as shown in Figure 9. Note:
- Cables must be bundled with the hook-and-loop fastener strap to ensure full range of movement of the cable management arm.
- Make sure that the cables do not sag below the U space so they cannot interfere with the lower systems.
- Allow slack in all cables to avoid tension in the cables as the cable management arm moves.
Figure 9. Securing the cables with hook-and-loop fastener strap - Optional: You can
install the cable management arm assembly on the opposite side, as
shown in Figure 10.
- Press the release buttons 1 and slide the mounting brackets 2 out of the cable management arm.
- Rotate the cable management arm 3 .
- Flip the mounting brackets 4 .
- Insert the inner bracket (marked with a capital letter I) and outer bracket (marked with a capital letter O) into the cable management arm 5 .
Figure 10. Installing the cable management arm on the opposite side - Insert the M6 screws to the rear of the slides, as shown
in Figure 11. Use a cable tie to secure the free end of the cable management
arm to the rack, if needed. See Figure 11.Figure 11. Securing the cable management arm and the file module in the rack for shipping if needed.
- Slide the file module into
the rack until it snaps into place. To slide the file module out
of the rack, press on the release latches 1 . Note: When you move the rack cabinet, or if you install the rack cabinet in a vibration-prone area, insert the M6 screws 2 in the front of the file module. Refer to Figure 12.Figure 12. Installing the front screws
Parent topic: Installing the hardware